Industrial Engineering

Identify the various elements of the operations management input, transformation, output process?

Neenah, Wisconsin

8 pt approximates to 66 lb cover, or card stock 10 pt approximates to 80 lb cover 12 pt approximates to 92 lb cover and so on... so to answer your question, the difference is that they are different stock. 14 pt is heavier than 80 lb.

I would use a butterfly valve to set the flow and a pitot tube to measure it. Nexus Valve makes a good one and it is price competetive as well.

A darling ton is a beta current multiplier. it output can be used to drive low impedance device

A lock washer overlaps itself when it is new so that when you tighten the nut down the pressure causes it to flatten out and in turn put pressure against the nut and whatever it is against. The pressure plus the gap in the washer helps prevent the nut from turning.

The CADA allows you to jet in surface pipe and drill out without making an additional trip out of the hole. The 36" relies on skin tension to stay in place, and after observation from the ROV the CADA will release the BHA and allow you to drill out the next section of casing while all returns are coming up through the pipe. Low fracture gradients in surface section don't allow returns on the backside of pipe.

if its standard wrought carbon steel, the psi should be just about in the 100,000psi range. The last two digits of the designation, 75, are the carbon content. 0.75%. the higher the carbon content, the higher the tensile strength.

The ultimate tensile strength of a steel such as AISI 1075 varies depending upon the heat treated condition and hardness. The tensile strength of a steel can be approximated from the hardness using hardness conversion tables found elsewhere on the web.

faulting

It's how much a structure can hold' for example, a book case, it needs to be strong and stable to hold the books, if its not the mass of the books will cause the book shelf to break.

Smv is a pre calculated time while sam is calculated during any operation evaluation.

Tanveer Alvi

You will have a 1:1 ratio isolation transformer.

The difference between a latch and a flip-flop is that a latch does not have a clock signal, whereas a flip-flop always does.

Apart from the clock signal difference,

~ Latch is a level sensitive device while flip-flop is an edge sensitive device.

~ Latch is sensitive to glitches on enable pin, whereas flip-flop is immune to glitches.

~ Latches take less gates (also less power) to implement than flip-flops.

~ Latches are faster than flip-flops.

Many stainless steels are stronger. It's also more corrosion resistant.

edwin drake

Some times on/off valves are to large to be actuated using one solenoid valve,but most of the on/off valves are being actuated using only one solenoid valve

1.368

56/23/35/23/35 it will vary depending on the board you carry, like medium can be 26.

Look for the meaning of one lay length of a mooring hawser

0.01Mpa

...It will be what ever your suction pressure is.

turbine

According to:

http://en.wikipedia.org/wiki/Parts-per_notation

PPM (Parts per Million) is a unitless quantity, therefore it does not equal a distance.

As in water filtration, this would be equivalent to 0.5 parts of a particular dissolved solid to 1 million parts of water.

0.5 ppm Total dissolved solids are achieved in water using Reverse Osmosis plus a DeIonizing filtration, or through steam distillation.

This is steel, the high-tensile kind to be exact. Hi-ten steel is pretty light, and decently durable. However, other materials are lighter and/or more durable. The only real advantage of hi-ten steel is that it's the cheapest. If you take a look at the bikes of BMX bike manufacturers, you'll see that their lower-end bikes are made out of steel. This is fine for most people, but if you actually do any EXTREME stuff with your bike, it's not built for performance.

business oriented,good process knowledge,good communication skills and good intra personal skills.