0
Late Model 1979-New Ford Mustangs
The 1979 model of Ford Mustang was based on the larger Fox platform that featured larger trunk and restyled interior to accommodate up to four people. It was available in three body styles – convertible, coupé and hatchback.
8,314 Questions
How many quarts of oil does a 2006 mustang use?
The 4.0L V6 takes 5 quarts of oil The 4.6L V8 takes 6 quarts of oil
Your 1997 Ford Mustang 3.8 v6 starts then dies?
If a 1997 Ford Mustang with 3.8 v6 starts and then dies, it could be glitch with the anti-theft system. There could also be an issue with the ignition connections or low fuel pressure.
What is the spark plug gap for a 2.3 1993 mustang?
.044 inch spark plug gap for the 2.3 L - 4 cylinder engine in a 1993 Ford Mustang
How do you install a driver glass window on an 89 ford mustang LX 4 cylinder?
It is a little aggrevating but not that hard,remove the door panel and plastic,you should see the window or what is left of it,unbolt it from the track.It has been awhile since I replace mine but I think that you just angle the new window putting the front in first and slide it down to the track and bolt it up.You may want to put some tape on the top with enough slack on it so you can use it slide the window up or down until you can get it in the track. It is a little aggrevating but not that hard,remove the door panel and plastic,you should see the window or what is left of it,unbolt it from the track.It has been awhile since I replace mine but I think that you just angle the new window putting the front in first and slide it down to the track and bolt it up.You may want to put some tape on the top with enough slack on it so you can use it slide the window up or down until you can get it in the track.
Where is the air pump on a 99 mustang?
It is under front passenger side bumper box mounted to frame. air hose runs inside belt path so you should be able to follow it to the pump.
What is the engine oil capacity for a 2002 ford mustang gt?
5.7 liters ( 6.0 quarts ) with engine oil filter change , according to the Owner
Guide
aod stands for automatic over-drive and is a common ford transmission
Where is the output shaft speed sensor circuit on a 2002 ford mustang gt?
here is a picture of where it is http://i26.photobucket.com/albums/c1...r_/4R70W_1.jpg
How do you know if your transmission is going out in your 2000 mustang?
That's easy, the shifts will seem to not be as fluid. They'll be rough, the car might seem to not want to initially move even though the tires are on gravel and not rotating at an excess speed.
the 84 302 'can' fit into the 88gt, but the width of the small block will be a bit to big to fit in the 88. you'l need to plasma cut 'or any way of cutting' oway at least 3 inches off the lower firewalls on the pasenger side area.
Where is the radiator fan control relay on a 1985 ford mustang located?
Hey man, I had the same problem until yesterday that I found the relay. It depends on the year of the car. You have two options:
- Check on the Constant Control Relay Module (CCRM). This solid-state device also contains the EEC power relay and the fuel-pump relay (follow the link below for instructions where is located).
- If your car doesn't come with the CCRM, check inside the car, driver's side, underneath the instruments panel near the steering column. You will see a little black box with several wires (check the second link for a reference on how it looks). There is where I found the relay on my car, and I'm pretty sure it is the one. Just follow the wires and make sure those matches with the ones going to the electric fan.
Read more: How to Replace a Mustang LX Radiator Fan Relay | eHow.com http://www.ehow.com/how_6555445_replace-lx-radiator-fan-relay.html#ixzz0rlqqoplF
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_Relay-BWD_18970095-P_588_R%7CGRPRELAAMS_568399322___
Good luck.
How do you remove and install a distributor in a 1965 Ford Mustang with a 289 V8 engine?
Remove the distributor cap. Remove the bolt in the clamp holding the distributor base to the motor, using a 1/2 inch box-end wrench. lift the distributor straight up. Note the orientation of the rotor. When reinstalling the distributor you'll need to stick it back in there with the rotor pointing in the same direction or the timing will be way off. The rotor will rotate slightly as the distributor goes back in. Also, the oil pump drive shaft is driven by a hex shaped hole in the bottom of the distributor. You have to wiggle it around a bit to get the distributor to slide down onto the oil pump drive shaft. Once you get it back in snug up the clamp bolt, put the cap back on the distributor, start the car and check the timing with a timing light. Adjust as needed by rotating the distributor. When the timing is right, and you do in fact have oil pressure, tighten up the clamp bolt.
Is the 1986 mustang front bumper interchangeable with 1987 and up?
Yes and with a few minor fiberglass resin patches it will not have any break points from body.
What is the weight of a 2000 Ford Mustang gt?
about 3200 lbs. I hear of people weighing them at 3180 though.
What is the engine oil capacity for a 1998 Ford Mustang 4.6?
The 1998 Ford Mustang owners manual shows 5.0 quarts ( 4.7 liters ) WITH FILTER CHANGE
