Nissan Pulsar

you have to find your belt tenstioner they are all different but they are fairly simple to adjust loosen too remove belt it should only have one

When the dash lights dim on the Nissan Pulsar SS 99 with the use of the turn signal, it is usually an indication of a bulb burned out in the turn signals. It can also mean that the flasher is bad and taking too much juice.

Because each lifter is worn differently on each cam lobe. No lifter are cam lobe is wore the same. If you don't put the lifters back in the same spot that they were installed in when they were NEW then it will cause the cam lobes and lifters to wear out like FAST.

If you are installing new lifters on an old camshaft then it does not matter were they go. THEY MUST GO BACK IN THE SAME PLACE.

The 1998 Nissan Pulsar S-RV typically has a fuel tank capacity of approximately 50 liters (about 13.2 gallons). This size allows for a decent driving range, suitable for both city and highway driving. Always refer to the owner's manual for the most accurate specifications.

To remove the tail lights on a 2004 Nissan Pulsar, first, open the trunk and locate the access panel behind the tail light assembly. Remove any screws or clips holding the panel in place, then disconnect the electrical connector from the tail light. Finally, unscrew the tail light assembly from the body of the car and gently pull it out to remove it completely.

To adjust the handbrake on a 1998 Nissan Pulsar, first, ensure the vehicle is on a level surface and securely raised with jack stands. Remove the center console trim to access the handbrake mechanism. Locate the adjustment nut on the handbrake lever; turning it clockwise increases the tension. After adjusting, test the handbrake to ensure it holds the vehicle securely when engaged. Always consult the vehicle’s service manual for specific instructions and safety precautions.

To change the reverse idler bearing on a 1988 Nissan Pulsar NX, first, ensure the vehicle is safely raised and supported. Remove the transmission by disconnecting the necessary components, including the driveshaft, shifter linkage, and electrical connections. Once the transmission is out, disassemble it to access the reverse idler bearing, which may require removing the retaining clips and gears. Replace the old bearing with a new one, reassemble the transmission, and reinstall it in the vehicle.

The rear windshield of the Nissan Pulsar CJ1 and the Nissan B14 Sunny are not directly interchangeable, as they have different dimensions and designs that cater to their respective body styles. While both vehicles belong to the Nissan family and may share some design elements, the specific curvature and mounting points of the windshields differ. It's always best to consult a parts catalog or a professional for accurate compatibility information.

In a 2000 Nissan Pulsar, the fuel filter is typically located along the fuel line, between the fuel tank and the engine. It is often mounted on or near the chassis, close to the fuel tank or under the vehicle. To access it, you may need to lift the car and inspect the underside. Always consult the vehicle's service manual for precise location and replacement instructions.

The Nissan Pulsar CD player is typically manufactured by Nissan itself, as part of the vehicle's audio system. However, specific components, such as the CD player, may also be sourced from third-party suppliers or manufacturers that specialize in automotive audio equipment. The exact maker can vary based on the model year and market.

On the Nissan Pulsar N13 model from 1990, the timing marks are typically located on the crankshaft pulley and the timing cover. You can find the marks on the crankshaft pulley aligned with a reference point or notch on the timing cover. Additionally, there are often corresponding marks on the camshaft to ensure proper alignment when setting the timing. Always refer to the vehicle's service manual for specific details and diagrams related to your engine.

To change the water pump on a 1992 Nissan Pulsar hatchback, first, disconnect the battery and drain the coolant. Remove the serpentine belt and any components obstructing access to the water pump, such as the timing cover. Unbolt the old water pump, clean the mounting surface, and install the new pump with a new gasket. Reassemble the components, refill the coolant, and reconnect the battery before starting the engine to check for leaks.

The valve clearance for the Nissan Primera E-P10 with the SR18DE engine is typically set at 0.25 mm (0.010 in) for the intake valves and 0.30 mm (0.012 in) for the exhaust valves. It's important to consult the vehicle's service manual for specific specifications and adjustments, as they can vary slightly based on the model year or specific engine configuration. Regular checks and adjustments ensure optimal engine performance and longevity.

In a 2003 Nissan Pulsar, the fuse for the lighter is typically located in the fuse box under the dashboard on the driver's side. You can find the fuse box by looking for a panel that can be removed or opened near the steering column. The specific fuse for the lighter is usually labeled in the fuse diagram, which can often be found on the inside of the fuse box cover. If the lighter is not functioning, checking this fuse for any signs of damage or a blown connection is a good first step.

Yes, the nut on the left-hand rear axle of the Nissan Pulsar typically has a left-hand thread. This means it is tightened by turning it counterclockwise and loosened by turning it clockwise, which is opposite to the more common right-hand thread. It's always advisable to consult the vehicle's service manual for specific details regarding your model.

On a Nissan Pulsar N15, the thermostat is typically located in the engine bay, near the engine block, where the upper radiator hose connects to the engine. To access it, you usually need to remove the upper radiator hose and sometimes the housing that contains the thermostat. It's advisable to consult the vehicle's service manual for specific details and diagrams.

To add transmission fluid to a 1990 Nissan Pulsar with an automatic transmission, locate the transmission dipstick, which is usually found near the back of the engine bay. With the engine running and the transmission in park, pull the dipstick out, wipe it clean, then reinsert it to check the fluid level. If the fluid is low, remove the dipstick again and use a funnel to add the appropriate type of transmission fluid through the dipstick tube, being careful not to overfill. Always check the owner’s manual for specific fluid requirements and capacity.

To find a diagram for the timing chain marks for a 1992 Nissan Pulsar with a GA15 engine, you can check the vehicle's service manual, which often includes detailed diagrams and specifications. Additionally, online resources such as automotive forums, repair websites like Haynes or Chilton, and YouTube tutorials can provide visual guides. You may also find helpful diagrams on websites like Nissan-specific enthusiast forums or through a local Nissan dealership.

On a 1994 Nissan Pulsar with an N14 chassis, the oil filter is typically located underneath the engine, near the oil pan. It can be accessed from beneath the vehicle, and you'll need to look towards the front or side of the engine block. Make sure to have oil catch pans ready, as some oil may spill when removing the filter.