0
Remote Control Devices
A remote control device is commonly an infrared device used to control electronic devices such as televisions and DVD players. It is usually powered by AA or AAA size batteries.
2,009 Questions
How long for first charge Ni-Cd 7.2V 700mah?
Depends on the charging rate, in Amps, of your charger. Very simply, if the charger current is rated at 450mA, then a 450mAh battery would require 1 hour to charge. Take the batter rating (450mAh) divided by the charger current rating (450mA), which equals 1 hour. If the charger rating is only 100mA, then it would take 4.5 hours to charge the same battery.
Vivo plasma 46inch tv remote code?
There are more than one Vivo TV Universal remote codes for a plasma 46-inch TV. You can find a full list on the Remote Code List website.
How you programming RCA systemlink 8 AV?
There are different codes for the RCA system link 8 AV remote control. The code that is used depends on what type of device is being programmed. You can check out RCA's website to get more information on the specific codes.
How do you program a radio shack 5 in one remote?
I would like to know how do i program a radio shack 5 in one remote 15-2200.
Where can you find television remote codes for a vidao television?
Vidao codes are found in your TV Instruction manual on the page preceding the illustration of your Vidao Remote. My TV model is 32E66 but I have found that Vidao codes are the same for all models i have tested.
Try these:
VIDAO UNIVERSAL REMOTE CODES- Comcast or Direct TV : 100300 (confirmed)
- AT&T (U-verse): 1043
- RCA Universal: 0030
- Dish Network: 506
What is the vizio television code for the cisco hda-ir2 remote control?
Easier and no codes are required; do the following:
1. Turn the TV on with your TV remote.
2. On the new remote HDA-IR2, press "Prog" and "TV" buttons at the same time until the red LED is on; release.
3. Press the "TV" button again to start the auto search and aim it towards your TV.
4. The remote will cycle through the stored codes. The TV will turn "off" when the right code is log in. You should imediately press "Prog" to stop the cycling, the code will then be saved in the new remote.
5. Press the "TV" on the new remote; your TV should turn "on". If not start over again..you were slow at pressing the "Prog" to stop the search.
5. Next program the Volume control, Press "Prog" and "TV", release, and press "Vol-" ... new remote will blink twice. This will control your black box volume. You can set the black box to near max and control the volume using the TV volume.
6. Now press "Prog" and "TV", release, and press "Vol+". You now can control the volume of your TV. If the sound is compresse or fuzzy, lower the black box volume.
kaicho8888
How do I program my samsung DVD remote to operate my magnavox tv?
To program my Samsung Bluray remote for my Sony TV I had to turn on the TV then hold down the "TV Power" button on the remote and enter the numbers 35 while still holding down the "TV Power" button. You can try 48 if 35 doesn't work.
What are the att you verse remote control codes for an insignia lcd tv?
AT&T U-verse remote control codes for INSIGNIA HDTVs (mine is a NS-24E730A12 and I have a black remote control) are: 1034, 1035, 1040, 1398, & 1465.
What are the remote TV codes for Westinghouse lcd TV?
I contacted Westinghouse
1-800-701-0680
and was emailed
"ZW1112613 VR-40 Firmware for TW61901-S040C"I simply loaded the file to a thumb/jump drive and inserted it into the USB port on the TV. I also had to use a Samsung universal remote code. I have Comcast remote with the red "ok" button and the code was 10178. I am now able to adjust the volume and turn the TV off with the Comcast remote.It was a bit of a pain but now I no longer duel wield remotes in bed. I hope you find this helpful and that you post your own tips to pay it forward.
Why flat screen won't change with a universal remote control?
they will and do.. I have them hooked up as such. SOME older tvs - flat screens included" do not have the ability to unscramble the cable signal, so the signal needs to go thru a convertor box, so the tv can read that signal, and make into something you can view.
How do you program a multi code linear garage door opener?
These remotes are based on "pin switch" settings matching between the remote and the receiver (ie: electric gates or garage door opener) Your remote has an access door to access its battery and dip switches. They are a series of many little white switches that are either in the "up" position or the "down" position, from left to right. The device you are controlling (gate or door, etc) has similar switches set somewhere in its adjustment settings. You must match the position of the switches on the remote to exactly match the settings on the receiving device. Sometimes, you can just find a remote that already works, and simply make sure your remotes switches are matched to the switch settings of the remote that already works
What is the remote code for Toshiba 23hlv87?
I used 0094 but unfortuneately universal remotes sometimes have there own codes.
Where can one find universal remote control codes?
Most likely it would be found in the manual, or possibly on the remote, or even in the setup up guide when you first use the remote. You could also call the company or look up their codes online.
What are the bell expressvu remote codes for hisense lcd40v57ca tv?
The support person at Hisense gave me the device code of 748
The support person at Bell Expressvu gave me the device code of 759.
The Hisense web site as follows;
supplies me with device codes 178, 10019, 505 and 627 depending on your provider none of these seem to work on my lcd40v57ca tv. If they work on yours let me know.
How can you use a universal remote for coby converter box?
Here are the TV codes for your Coby TV: 500 and 001. I have also provided instructions on how to program the remote to your Coby TV.
Remotes: Basic (Television Only)
- Turn the Television On.
- Press and hold the clear TV button for three seconds until the LED flashes.
- Enter the three-digit code using the buttons on the number pad.
- Press #. Note: The LED will flash three times.
- Test functionality with the TV.
- Return to Step 2 if the remote is not able to turn the TV On/Off, change the volume and mute the television.
0538, 0565, 0225, 0221, 0517, 0100, 0736, 0067, 0586, 0617, 0039, 0066, 0473,
0400, 1938, 0660
How can you use ssh to find out who logged in on a remote system?
If an individual has the same username on the systems being check up on, they could use the command "$ ssh host who" at the prompt for who. This would bring up the listings for all the people who have logged on or off within a certain period of time on this particular system.
A remote area is a place where there is nothing around. No island, plave and food.
Why would someone need a sky remote tv code?
The average customer needs to know Sky remote tv remotes because it is very useful if you have many remotes and want to use just one universal remote.
How do you play a DVD with no remote?
well your DVD player should at least have a play button on it, so you dont have to use a remote everytime, but if it doesnt i guess youre screwed.
Where is the code search button in Phillips universal remote?
phillips cl034 manual Paste this into your browser to view the entire remote manual. You're welcome :)
http://rsk.imageg.net/graphics/uc/rsk/Support/ProductManuals/1500115_AD_EN.pdf
How do you program universal remote?
These days, almost all the electronic gadgets are accompanied by the remote controls. Programming a remote control is as easy as it is to use it. Remote controls come with codes and some without codes.
To program the remote with the codes, firstly, turn on the electronic gadget for which you are going to use this remote, by pressing the On and Off button. Then locate the Setup or the Code Search key on the remote control. These buttons may vary from remote to remote. Just hold on the setup or the code search key for 5 - 10 seconds or till the light on the remote turns on. Again it depends on the different remotes that the light will blink or be steady. If you are programming for your TV, press the TV button on the remote or whichever electronic device you are programming your remote for. Now use the numbers on your remote to enter the 3 or 4 digit code for the device. These codes are given in the manual given with the electronic gadget. If you have lost the manual, these codes are easily available on the internet too. Once you have found the code, enter it and you will notice that the light on your remote control has turned off. Now try using it to switch off your electronic device with the remote and if you can do that, your remote has been programmed.
As for the remote controls that come without the codes, the programming is a bit different and a little time consuming. After the light on the remote has turned on, start pressing the Up button for channels on your remote. You may have to do this many times, may be 5 - 10 minutes. As soon as the channel changes, your remote is programmed. Now turn your electronic device on and off from your remote to finish programming.
However, if you are not able to program your remote with the Up channel button, try it with the Power button on the remote. Press the button a few times till the device you are programming gets turned off. When it does get turned off, you have successfully programmed your remote control.
The Answers community requested more information for this question. Please edit your question to include more context. Universal what.
