0
2000 Saturn sl1 the dashboard temp indicator has always hovered at 14 you just had dealer replace thermostate and cts connector dash indicator hovers now 12 is there danger of overheating?
Wiki User
∙ 16y ago
To clarify my question "14" means one quarter of the way...."12" means half way. I have a 94 SL2 and was worried about that gauge hitting the half way mark, but Saturn dealer assured me they 'run hot' (the gauge) and this is normal. I now have a bad CTS and it's only hitting the 1/4 mark. Seems it was not working correctly at that 1/4 mark, and the repairs fixed that in your case. If it heads into the red, you have a problem. Hope this helped.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What is indicator zero connector?
ambot
Clicking sound under dashboard?
the indicator?
What do the dashboard lights mean in 2004 ford escape?
The yellow fuel dispenser warning light indicates low fuel. The red battery indicator light indicates the charging system is malfunctioning. The red high water level indicator light indicates the cooling system is overheating.
Why do your S80 indicators on dashboard work intermittently when actual lights are operating properly?
The dashboard indicator light might have a loose connection. The dashboard indicator light might have a corroded or loose ground wire.
Could you display indicator dashboard icons for jaguar x type 2002?
Could you display indicator dashboard icons for jaguar x type 2002?
How do you reset the srs light on a 2000 Honda civic?
These are the instructions out of the Honda Service Manual for 1996-2000 Civics: 1.) Make sure the ignition switch is OFF. 2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire. 3.) Turn the ignition switch ON. 4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off. 5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on. 6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds. 7.) The SRS indicator light indicates that the memory is erased by blinking two times. 8.) Turn the ignition swith OFF, and wait for ten seconds. Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult. Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
What makes the needle of the dash board engine overheating indicator go way past the red?
only 2 things can cause this. The most likely is that it is overheating... a lot the least likely is that the indicator is faulty or the wrong type.
What is a triangle with a circling arrow on BMW dashboard?
traction control indicator
Where can you find the indicator flasher unit in a proton wira?
if indicator flasher is signal relay then its underneath dashboard, driver's side..
You have a 1997 Honda civic and its srs light keeps turned on you want to know that how can you reset the srs light on?
These are the instructions out of the Honda Service Manual for 1996-2000 Civics:1.) Make sure the ignition switch is OFF.2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire.3.) Turn the ignition switch ON.4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off.5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on.6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds.7.) The SRS indicator light indicates that the memory is erased by blinking two times.8.) Turn the ignition swith OFF, and wait for ten seconds.Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult.Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
Front indicator light on the peugot 206 not working but indicator arrow on dashboard clicking fast?
you need to replace the bulb in the front...
What is the wrench and oil can indicator on the dashboard of a 3500 Chevy van?
maintenance required
