Auto Parts and Repairs
Chevy Camaro
Chevy Lumina
Toyota RAV4

Do you need to remove the crank pulley to change the oil pan gasket on a 1995 Chevy Lumina 3.1 auto 4dr?

212223

Top Answer
User Avatar
Wiki User
2015-07-15 18:38:38
2015-07-15 18:38:38

No, I wouldn't think so. I have a question, though? Why are you changing the pan gasket?

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the cylinder head from your 1992 Chevy Lumina engine. Remove the head gasket and clean the surface. Put the new head gasket on and reverse the process.

User Avatar

You will need to remove the cylinder head from your Chevy Lumina engine. Remove the head gasket and clean the surface. Put the new head gasket on and return the cylinder had to its original position.

User Avatar

Drain the water from your 1998 Chevy Lumina oil pan. Remove the oil pan retaining bolts. Remove the old oil pan gasket and clean the surface. Put the new oil pan gasket on and reverse the process.

User Avatar

I want to take off the pulley wheel off,from a 1992 chevy lumina apv van.

User Avatar

Fairly easy. remove the serpentine belt. Remove the pulley from the water pump. You need the sockets that fit those bolts and the sockets that fit the pump's mounting bolts. Get gasket sealer too.

User Avatar

Drain the oil from your 1993 Chevy will oh my not oil pan. Remove the oil pan retaining bolts. Remove the oil pan gasket and clean the surface. Put the new oil pan gasket on and reverse the process.

User Avatar

Easy job! Takes 15 minutes flat. First loosen the 4 pulley bolts. Remove accessory drive belt. Remove bolts, remove pulley. Remove bolts holding to pump to engine. Remove pump unit. Clean gasket surface with sharp wooden stick. NO METAL, you'll damage the gasket mating surface and assure leaks. Reverse procedure to install.

User Avatar

You can change the head gasket by removing the valve cover. Remove the gasket and clean the gasket surface. Put the new head gasket on the cleaned surface.

User Avatar

there should be 3 or 4 bolts that hold pulley on, just remove these bolts a pulley should come off. but remove belt first ! if pulley keeps turning while removing bolts. you can hold it stationary with a scredriver or similar.

User Avatar

You have to unscrew the tensioner bolt and remove the serpentine belt first, then change the pulley and replace the belt.

User Avatar

Remove the manifold and change the gasket. And voila!!!

User Avatar

Using a crescent wrench, pull up on serpentine belt tensioner and remove belt from water pump. remove pulley, remove bolts in a circular pattern around face of pump, and then the entire guts of the pump will come out including the impeller. The pump housing stays with block. Clean surfaces install new gasket with replacement and reinstall pulley and belt. Not too hard actually

User Avatar

Remove the belt from your 1997 Chevy Lumina alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.

User Avatar

Remove the exhaust pipe from the exhaust manifold. Remove the manifold bolts. Remove the manifold. Remove the manifold gasket and clean the surface. Reverse the process to install the new manifold gasket.

User Avatar

Remove the valve cover. Remove the head bolts. Remove the head. Remove the head gasket. Clean the surface of the head. Reverse the process to install the new head gasket.

User Avatar

Remove the old filter and make sure you remove the old gasket, there should only be 1 gasket.

User Avatar

Drain coolant Loosen and remove bolts that hold fan in place Remove fan belts Remove pulley Remove hoses unbolt and remove water pump Clean engine mounting surface completely install new gasket and pump reverse to install

User Avatar

You remove no pulleys. Just loosen the belt and then remove the alternator.

User Avatar

i am going to change the valve cover gasket on my 97 cadillac catera, what do i need to remove and do? Is it hard?

User Avatar

First, remove intakes and anything else in the way. Remove valve cover. Remove head. Remove old gasket. Clean gasket surface. Reinstall. You're welcome.

User Avatar

Take off belt, remove bolt in center of pulley, replace with new pulley (comes with bearing). Reverse to install Take off belt, remove bolt in center of pulley, replace with new pulley (comes with bearing).

User Avatar

Remove the valve cover. Unbolt the head and remove it. Take the old gasket off and clean the gasket surface. Apply the new gasket and reverse the process.

User Avatar

drain radiator of coolant, remove serpentine belt and remove pulley on water pump. If the pulley has 4 little bolts on it then loosen and pull the pulley off. If there are no bolts on the outside of the pulley then its pressed on, you can remove it yourself with a blowtorch but its hard to get off and on correctly. Remove the bolts holding the pump on and pry the pump off the engine, this will be hard most likely due to the gasket holding the pulley to the eingine. There will be coolant that will come out due to coolant you couldn't drain by the radiator...just have a container under car to catch coolant. Once removed scrape all the old gasket material off the engine... there is a gasket remover tool but a razor blade workls just fine. Once removed clean area well and apply gasket to new pump with gasket sealer and place pump back onto engine. Tighten bolts and replace pulley and belt, fill with coolant and top off as needed. be sure to purge the coolant systemof air after any major coolant work. The repair is relatively easy as loong as you have the right sockets for the job...good luck!

User Avatar

How to remove steering wheel on Chevy lumina 2000


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.