Starters and Ignition Systems
Chevy Blazer S-10
1995-2005 Chevy Cavaliers
Chevy Nova

How do you remove the ignition cylinder lock from a 1970 nova?

888990

Top Answer
User Avatar
Wiki User
2010-12-16 15:18:34
2010-12-16 15:18:34

If you pull the turn signal swithch out of the way ther is a small slot with casting flash in it, there is a screww stand in the same are, take a a small flat screwdriver and punch out the casting flash, turn the ignition to the "run" position and take a flat tool like a feeler guage and push down on the lock cylinder release, it will take afew tries, you will feel it push in about 1/16" or so, keep pushing and pull the cylinder out at the same time. My email is dpw28@astound.net, I could send a picture if you read this before I finish rebuilding my column. Dennis

He's right I had to do the same once after I couldn't get her to crank. I realized something was altered in the interior when I Bought it from a guy in Tennessee. Sammy.

i have a question, how ya supposed to turn it to the ON position when the key wont work.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the retaining ring from the top of your 2000 Mercedes-Benz ignition lock cylinder. Slide the ignition lock cylinder out and remove the wiring harness.

User Avatar

Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.

User Avatar

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.

User Avatar

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.

User Avatar

The 1994 Pontiac Grand Am ignition lock cylinder is held in place by the retaining ring at the top of the cylinder. Remove the retaining ring. Remove the wiring harness from the back of the cylinder.

User Avatar

Begin by removing the retaining ring at the top of your 1996 Chevrolet Silverado ignition lock cylinder. Slide the ignition lock out and remove the wiring harness. Reverse the process to install your new ignition lock cylinder.

User Avatar

To change the ignition lock cylinder in a 2001 Chevrolet Tracker, first disarm the air bag system. Then remove the clock spring assembly to be able to remove the old ignition lock cylinder and replace with a new.

User Avatar

what lock cylinder?door or ignition? door is simple, remove inner door panel, unhook rods attached to lock cylinder, remove retaining clip

User Avatar

Ignition switch and lock cylinder removal 1988 Dodge Ram 50.Disconnect the negative battery cable from the battery.Remove the steering column cover to gain access to the ignition switch/lock cylinder.Using wire cutters, remove the cable band.Remove the bolts that hold the ignition switch/lock cylinder to the steering column.Unbolt and remove the key reminder switch and remove the switch lock cylinder from the steering column.

User Avatar

Remove the retaining ring from the top of your 1997 Chevrolet 1500 ignition cylinder. Slide the ignition cylinder out and remove the wiring harness.

User Avatar

Begin by removing the retaining ring at the top of your 1996 Mercury Tracer ignition switch. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the cylinder. Reverse the process to install your new ignition lock cylinder.

User Avatar

Removing a ignition lock cylinder from a 2002 ford windstar with no key

User Avatar

You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.

User Avatar

if it is the ignition lock cylinder, first disconnect the battery, you need to remove the steering wheel ,turn signal switch , etc, then you need to insert the ignition key into the lock cylinder, turn it to the run position,then pull the cylinder out, reverse the operation to install the cylinder,

User Avatar

How to remove and replace ignition lock on 94 escort lx wagon1.9

User Avatar

do you mean the door or ignition?

User Avatar

The ignition lock switch is found under the steering column on a 2004 Honda Civic. Remove the steering column and ignition switch. Loosen the mounting screws that hold the cylinder in place. Pull and replace the lock cylinder.

User Avatar

1. Close the vehicle doors.2. Turn OFF the ignition.3. Remove the key from the ignition.4. Press and hold the driver side door lock switch in the UNLOCK position.5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).10. Perform the previous step to program up to four transmitters (including your old ones).11. Remove the ignition key in order to exit the Program Mode

User Avatar

You will have to remove the horn pad and the steering wheel which requires a special puller. Then you need a compressor for depressing the wheel lock. Remove the turn signal switch and there will be a slot to insert a small blade screw driver. Depress the pin and pull the lock cylinder out. Insert the new one and you will feel it lock in place.

User Avatar

Attach the wiring harness to the end of the ignition lock cylinder. Slide the ignition lock cylinder into the slot. Tighten the retaining ring at the top of the cylinder.

User Avatar

pull steering wheel off, remove the steering lock disc, then remove the signal light switch assembly to gain access to the retaining screw that holds the lock cylinder in place,

User Avatar

You will need to attach the wiring harness to the end of your 1984 Chevrolet Blazer ignition lock cylinder. Slide the cylinder into the cylinder slot. Secure the ignition lock cylinder with the retaining ring.

User Avatar

The ignition lock cylinder on a 2006 Chevy Cobalt is removed by popping off the steering column cover and inserting a screwdriver into the release hole. The cylinder can then be pulled from its housing and replaced.

User Avatar

I'm wondering if a locksmith is capable of getting your ignition lock cylinder to rotate to the on/run position so the ignition lock cylinder release can be depressed to remove it ? I'm also wonderering what they would charge for that service, because I was charged $30.00 and taxes to open my door lock on my house.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.