0
How do you remove the seat on a 2000 Yamaha road star using ignition switch?
Wiki User
∙ 15y ago
The procedure is as follows: Insert the key into the ignition switch. Without pushing down, turn the key as far in the counter-clockwise direction as you can. You should hear a click sound from the front end of the seat. The seat is now ready to be removed by lifting on the front portion of the seat (the horn) and lifting upward.
However, sometimes the seats can be fickle. Owners have found that the locking mechanism can be stiff and pushing down on the horn of the seat while turning the key will do the trick.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you remove key switch Ford F-350?
Disconnect the negative battery cable, using a socket. Remove the lower steering column shroud, using screwdriver. Lower the steering column by removing the three 15 mm nuts in the column support bracket on the instrument panel, using a socket. Pull the electrical plug out of the ignition switch. Remove the two bolts securing the ignition switch to the steering column, using the appropriate socket. Lift the ignition switch off the column. Hope this helps.
Where is the holding pin on a 95 Ford Escort ignition lock you looked and could not find?
I just replaced the ignition switch and lock on my '96 Escort. They come as one unit, so you can't just replace the lock tumbler. Remove the steering wheel (using caution for the airbag), and then remove the multi-function switch. Now you can remove the ignition switch and lock.
How do you remove and install ignition switch in a ford 1977 F250?
there are 3 notches on the front of the ring around the ignition switch. use a a flat head screwdriver in one of the notches to help turn that ring. reach under the dash and take ahold of the ignition switch main body. using the screwdriver loosen the ring by pulling the screwdriver in a clockwise direction until ring is loose enough to remove with finger pressure. Remove ring and slide ignition switch out through the underside of the dash. Carefully unplug the wire plug from the switch and match plug to new switch box. To install reverse process.
The ignition switch will not turn at all What do you do?
Are you using an original key, or a replacement that has the proper security computer chip located in the fat plastic part of the key? If not, the car's security system will keep the ignition locked and will not allow you to turn the ignition switch. ALSO: some earlier models of Focus had ignition switches that were a problem. If you ARE using the correct key and can't turn the switch to start the car anymore, the ignition switch may have to be replaced.
How do i hotwire my Honda Accord LX 1992?
Examine the ignition setup. There should be a panel with five to eight wires clipped to the rear of the tumbler. Remove the panel and try to manually turn the ignition switch using a screwdriver. If you can do this, then you are done!
How do you remove the ignition barrel on an 87 Ford Laser?
Remove the steering column surround and you should see a black round thing on the left hand side, this is the ignition switch. Remove this and you will see there is one screw holding the ignition barrel on, remove and you then need to insert your key and turn it to the ACC position. you should now be able to withdraw the barrel using the key but take care not to snap the key off in the barrel
How do you remove ignition switch from steering column on 84 Pontiac fiero?
you have to remove the steering wheel then using a lock plate removal tool depress the lock plate and removed the clip that holds it in place then remove the lock plate then remove the screws from the turn signal switch and pull it up slightly then remove the screw that hold the lock cylinder in place then remove the lock assembly
Why does your Yamaha pw50 die when switched to the run position?
The reason your PW50 is cutting out when switched from the start position to the run position is because the contact points on the switch it self are worn down! The quick fix for this problem is to carefully remove the small plastic sliding switch block being careful not to loose the ball or spring! You will have to remove the copper contact plate with a fine flat or flat precision type screw driver and carefully tap on the 3 points on the reverse side of the contact plate again using a precision type screw driver and a small hammer.... It would be a good idea to clean the contact points on the wired contact block with some contact cleaner! Put the switch back together unplug the ignition switch (wire harness) and single black ground wire and test the switch with a multimeter just to make sure that the points are making proper contact! This is how I fix the ignition switches on the Yamaha's and other Japanese bikes with similar ignition switches!
How can I affordably get my F350 ignition key to turn Thanks?
if it is 92-97 remove steering column covers then using a small drill locate small hole on the underside of column under the ignition switch drill out pin inside and slide switch out then spend about 13 dollars on new switch slide new one back in put covers back on column
How do you remove the ignition switch from a 1986 Cadillac ElDorado?
Remove the bezel from around the radio, this will expose two hidden screws. Remove these screws and about eight other screws to remove the lower dash panel below the steering wheel. Remove the two large bolts and drop down the steering column. The ignition switch is a white module on the top left of the steering column. Remove the connectors along the right and the two screws along the left. Lift up the switch to disengage the mechanical link to the key tumbler to remove. Good luck finding a new module, I couldn't locate one for mine, so I just reconditioned my old one using some contact cleaner. If you're talking about the ingition cylinder, remove the steering wheel and turn signal switch. Remove the buzzer switch (white plug with a couple wires) located at about 4 o'clock by pulling straight out with a pair of needle nose pliers. This will expose the cylinder retaining screw. Remove the screw, and with the ignition switch in the locked position, pull the cylinder straight out...
How do you remove the ignition switch on a 77 Dodge?
Remove horn ring, remove steering wheel, get steering wheel puller from Auto Zone rental program, remove big nut using wrench, then pull off piece behind steering wheel with wheel puller. Remove turn signal switch, then it's a little fuzzy from there (I'm working on the same thing now with a '73 Challenger.) Eric
How do you remove a key that is stuck in the ignition?
See You-Tube Video : http://youtu.be/lBNUuO4ldfI How to Remove a broken key from an Ignition. Using the Broken Key Extractor Kit from: www.WedgeCo.com
