answersLogoWhite

0


Best Answer
Copy

The harmonic balancer must be removed to change the sensor because the crank position triggering rings on the back of the balancer are entwined with the pick-up, Sorry

User Avatar

Wiki User

โˆ™ 2015-07-15 21:15:50
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the crank position sensor on a 92 Olds Cierra 3.3L and can it be done with out pulling the harmonic balancer?
Write your answer...
Submit

Related Questions

How do you replace harmonic balancer in 1999 Lincoln town car?

Harmonic balancer replace


How do you replace the harmonic balancer on 2000 Infiniti I30?

how to replace harmonic balancer on a 2000 infiniti i30


What problems can occur after replacing a harmonic balancer?

how to replace harmonic balancer 3.4 v6 2001 grand am gt?


How do you replace a harmonic balancer Mercury Topaz 1992?

The harmonic balancers function is to reduce vibration between the engine and the crankshaft. To replace the harmonic balancer requires a specific tool available at an auto parts store. Loosen the crank pulley via 4 bolts to access the balancer. Using the tool remove the harmonic balancer from the crankshaft.


Where is the crankshaft position sensor located on a 2002 impala 3.8L engine?

It is located behind the crankshaft harmonic balancer pulley on the bottom front of the engine. The right lower splash shield and harmonic balancer pulley must be removed to replace it.


How do you change the crank position sensor on 1996 buick?

Actually, you don't replace the sensor itself. The crazy thing is part of the harmonic balancer, and you have to replace the whole thing.


Why does your harmonic balancer make noise?

It shouldn't make noise. If it does, replace it!


If the harmonic balance is bad can you repair it or replace it?

I would contact the local parts store and replace the harmonic balancer if you think it is bad. a bad balancer can cause failure in the crankshaft bearings because of the shake.


Does the intake manifold on a 1999 Buick Century have to be removed in order to replace the cam shaft position sensor?

no it;s behind the harmonic balancer take off passenger right front tire and you can get at it. you will need a wheel puller to pull the harmonic balancer off


Where is the camshaft position sensor on a 1992 Oldsmobile 88?

Its under the harmonic balancer cover. You can see the wiring on the right (front) side of the cover. Pull the harmonic balancer to replace it, make sure you line-up the teeth right in the magnetic pick-up.


How do you know when you need to replace the harmonic balancer in your car?

Am unsure of what you are asking. The harmonic balancer is a lifetime part of the engine and does not need replacement based on a time or mileage requirement.


Where is cam position sensor located on 1993 Chevy lumina?

Assuming that it is a 3.1 V6, as most of them are, there is no cam sensor. Only a crankshaft sensor. It is located behind the harmonic balancer. To replace it the balancer has to be removed.


How do you replace rubber bushing in a harmonic balancer?

you don't -Buy a new one


How do you repair a harmonic balancer for a 2001 Chrysler sebring?

You dont repair it...you have to replace it.


What size socket will BE needED to replace a harmonic balancer on a 1998 Malibu?

15mm


How do you fix a harmonic balancer on a 2001 Chevy impala?

There is not much you can do with a bad balancer other than replace it with a new one.


Crank sensor location on a 1989 Oldsmobile delta 98?

The crank sensor is located behind the Harmonic balancer. Try not to break the rubber within the Harmonic balancer when removing or on the safe side replace both the Crank sensor and the Harmonic balancer ( the big pulley on the bottom - most part of the engine.)


Where is the crankshaft position sensor on a 1995 Oldsmobile silhouette?

On the 3.8 litre engine its located on the forward side under the harmonic balancer. You need to pull the balancer to replace the sensor. The magnetic pick-up on the sensor rides in the stainless steel stotted track on the rear of the balancer.


What is the knocking noise in engine 3.8 liter Pontiac grand prix?

Replace the Harmonic balancer


How do you replace the harmonic balancer on a Chevy small block?

There is a bolt in the center of it, 5/8ths inch. Remove that, then the three 9/16ths bolts in a triangle pattern, which removes the pulley. Then, you will need a harmonic balancer puller, as they are pressed on.


The main flywheel off the crankshaft that runs the belts pulleys on your 1986 Buick Lesabre is vibrating causing a rattling clanking sound how do you resolve this?

sounds like the rubber damper is worn on the harmonic balancer. if this is the case you will have to replace the harmonic balancer.


Where is the crankshaft sensor on a 1989 Buick Regal 2.8 V6 and how do you replace it?

at the front of the engine,next to the harmonic balancer


How do you replace harmonic balancer on 1993 f 350 with 351 motor?

first remove serpintine? fan belt then remove large bolt in middle of harmonic balance. this bolt usually has left hand thread next with a harmonic pulley ,puller, remove harmonic balancer.when removing this, there is a key in the balancer and shaft if a new key did not come with new balancer,make sure not to loose the old one install new balancer with key.use the bolt to pull balancer up tight where it needs to be and use proper torque on bolt


How do you replace a Crank Position Sensor on a 1992 Oldsmobile Regency 98?

It takes a special tool. I got mine from Autozone and had a guide from them on how to replace it. You'll have to remove the belt and harmonic balancer and access it through the passanger side front tire.


Where is the Crank shaft sensor 1989 cutlass ciera?

Behind the harmonic balancer. You will need to remove the right front tire, remove the access panel to the engine (through the wheel well), remove engine belt, remove harmonic balancer & pulley with a puller. Remove & replace crank sensor, align sensor with an alignment tool, replace balancer with an installer tool.. BE VERY careful with the balancer, the backside of it has a hall effect style blades. bending these blades will junk the balancer.