Best Answer

Perhaps the question asker is referring to the ignition coil module that feeds to the distributor. This coil is mounted to the passenger side of the intake manifold with (2) 10 mm hex screws. Replacing this is a simple matter of unplugging the electrical connections, unbolting from the manifold and installing a new coil in the reverse procedure. Please note that the '99 suburbans still used the 5.7 liter, L31 RPO engine and are different from the pickup truck line which had already switched over to the new 6.0 engine line.

User Avatar

Wiki User

โˆ™ 2007-04-17 14:16:59
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the ignition module on a 1999 Suburban?
Write your answer...

Related Questions

Where is the ignition module 1999 Laredo?

The engine computer is the ignition module.

How do you replace a starter on a 1999 Chevy Suburban?

How do you replace a starter in a 1999 suburban

How to replace the ignition module in a 1999 Ford Contour?

What engine? Ford contour 2.0L DOHC eng. distributorless ignition are controlled by the main PCM There is an ignition module on the 99 contour 2.0 with automatic transmission. It is shown in the schematics for this model.

Where is the ignition module on a 1999 4 cylinder Chevy S 10?

The 1999 Chevy S 10 pickup truck ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.

How do you replace ignition lock 1999 vw beetle?

how to replace ignition lock for 1999 vw beetle

Where is the ignition module on a 1999 Chevy Astro van?

Right under the ignition cap.

Where is the Retained Accessory Power Module located at on a 1999 Chevy Suburban?

There is none!

Where is the ignition module located on a 1999 Mercury villager?

Inside the distributor

Do you need to replace the ignition lock cylinder when you replace the ignition switch on a Pontiac Sunfire 1999?

No, not if it is not defective. If the ignition switch is defective then that is all you need to replace.

Where is the ignition control module on a 1999 Ford Crown Vic?

The Ignition control module is mounted under the hood. It is on the fire wall right beside the hood strut,

Where is the ignition module located on a 1999 Plymouth Breeze?

It is part of the engine computer.

How do you install ignition control module on 1999 vw passat turbo?

Pull the cover off the air intake box, unclip the two wires from the old module, remove screws. Screw in new module and replace wores and box. job done

Does a 1999 Chevy Suburban have a transmission module?

No separate module. It is controlled by the Powertrain Control Module (PCM) which controls engine and tranny. Under hood on rear driver side.

How hard is it to replace the heater core in a 1999 GMC Suburban?

Answernot hard

How do you replace a radiator on a 1999 suburban?

Unscrew a few screws and pull it out

Where is the ignition module on a 1999 Ford Windstar?

If you're looking for a stand-alone ignition controlmodule, there isn't one on the Windstar.This job has been transferred to the Powertrain Control Module (PCM) and its direct control of the coilpack.

Where is the wiper pulse module board located on a 1999 GMC Suburban?

it is located on the front of the wiper motor.

What is the recommended mileage to replace a 1999 Chevy Suburban fuel filter?

Replace it every 75,000 miles.

How do you replace the ignition switch on1996 Saturn sl?

ignition switch saturn sl 1999

How do you repair squeaking windshield wipers on a 1999 Suburban?

Replace the windshield wipers.

How to Replace window motor in a 1999 suburban?

How to remove the window motor from the regulator

Why does your 1999 suburban miss fire when idling or going below 2000 rpms?

To find the misfire, check the crankshaft sensor on the 1999 suburban. Check for the proper fuel pressure, and check the ignition coils.

What would cause a 1999 Chevrolet 350 to have no spark?

typically this means the ignition module is bad

How do you replace the ignition switch on 1999 Malibu?

please give instructions on replacing the ignition switch on my 99 Malibu

What are the causes for no spark on a 1999 Ford Ranger?

No spark can be as simple as a ecm fuse blown, a bad ignition switch, defective ignition module or a bad coil.