0
What direction to turn harmonic balancer bolt to remove harmonic balancer?
Wiki User
∙ 13y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Which direction do you turn the harmonic balancer bolt on a 1996 Sebring 2.5L engine to remove it?
You turn it counter clockwise to loosen.
How do you remove the harmonic balancer in a Nissan Maxima?
To remove the harmonic balancer from a Nissan Maxima, first you need to removed the center bolt. After that, you can use a puller to remove the harmonic balancer. Before you do this, make sure you disconnect the battery and remove the drive belts.
How do you replace harmonic balancer on 1993 f 350 with 351 motor?
first remove serpintine? fan belt then remove large bolt in middle of harmonic balance. this bolt usually has left hand thread next with a harmonic pulley ,puller, remove harmonic balancer.when removing this, there is a key in the balancer and shaft if a new key did not come with new balancer,make sure not to loose the old one install new balancer with key.use the bolt to pull balancer up tight where it needs to be and use proper torque on bolt
How do you remove a crankshaft pulley on a 67 Chevelle?
The crankshaft pulley unbolts from the harmonic balancer. The harmonic balancer can be removed from the crankshaft with a 3 bolt puller.
How do you change harmonic balancer on 1991 buick lesabre?
The flywheel has to be held in place by a holding tool, Remove the mounting bolt, then use a balancer remover to pull the harmonic balancer.
How do you remove the bolt on the harmonic balancer of a 1998 Lincoln Town Car?
you unscrew it
How do you remove the harmonic balancer on a 1996 dodge neon?
loosen the center bolt and get your self a harmonic balancer puller just make sure you loosen the center bolt enough but not too much but you need a balancer puller.
Remove Taurus harmonic balancer?
Remove belt,4 pulley bolts and remove pulley. Remove harmonic balancer bolt and washer,reinstall bolt with out washer,just in about half way.You will need a harmonic balancer puller.These are not very expensive about $20.00 or borrow one from somebody.You just thread the correct included bolts into the balancer where you removed the pulley bolts and will be pushing on the reinstalled balancer bolt.The balancer should clear the bolt head without the washer.This is so you don't damage the threads in the crankshaft.
How do you Remove a Harmonic Balancer on 1996 Chevrolet carprice classic?
You will need a harmonic balancer puller. Remove crankshaft bolt and washer, reinstall bolt without the washer approximately 10 turns. This will protect the threads in the crankshaft. Install puller and remove balancer. You cannot remove the balancer without this puller. They are inexpensive or try to borrow one.
What direction do you a turn bolt on a harmonic balancer on a 2001 Honda accord to take off?
Counterclockwise.
How do you remove the harmonic balancer bolt on a 2001 Corvette?
www.ls1howto.com may be able to help.
How do you remove the harmonic balancer in a 1995 Nissan Maxima GLE?
Start by removing the right front tire and support the vehicle with a jack stand. Then remove lower portion of the splash guard near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tensioner and then loosen the tensioner bolt (it is the one that's sticking straight up, you use a 14mm socket on it.). The power steering adjuster bolt will be accessed from the bottom near the power steering pump. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Remove belts. Then remove harmonic balancer bolt (19mm). If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller on to the harmonic balancer. (one finger on each side securely press into the belt groove.) The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.
