0
What is the size of the Bolt for the Serpentine Belt Tensioner?
Wiki User
∙ 14y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What bolt size is needed with serpentine belt tensioner for a 2000 Pontiac Montana?
15mm socket will fit the bolt. Do you mean what is the length of the bolt? I mean the length of the bolt.
How do you replace the alternator belt on a 1993 Dodge Shadow?
Depends on which engine. 3.0 v-6 has a serpentine belt. Move the tensioner with a wrench to get the belt off, then replace it. If a 2.5 eng., loosen the tensioner with 13 or 15 mm (can't remember which size), but back off the tensioner bolt. Then, you'll see the belt loosening. You may have to back off the bolt inside the tensioner as well. Re-tighten the same way.
How do you change serpentine belt 98 4runner 4 cylinder?
Find the appropriate size socket to go on the belt tensioner, put it on a ratchet or breaker bar. Rotate the belt tensioner counterclockwise, and that'll loosen the slack and allow you to remove the serpentine belt.
How do you loosen the tensioner for the serpentine belt on 2003 Chevy Malibu?
Use penetrating oil and correct size wrench.
How do you change a serpentine belt on a 2000 Dodge Ram 2500 pick up?
Take a breaker bar and a socket make sure it's the right size socket for the bolt on the tensioner, insert the socket on the bolt and take the tension off the belt and remove make sure you remember the routing so you can replace as you put it back on pull on the tensioner so you can slip the belt back on then when you have it in let the tensioner go and take the socket out and you should have just changed you belt.
1995 Chevy full size truck removal of the serpentine belt?
FIRST PUT A BREAKER BAR WITH THE CORRECT SIZE SOCKET ON THE BELT TENSIONER BOLT AND RELEASE THE TENSION ON THE BELT, WHILE DOING THIS SLIP THE BELT OF OF ONE OF THE PULLEYS. THEN SNAKE THE BELT PAST THE FAN AND ACCESORIE DRIVES. INSTALLATION IS REVERSE OF REMOVAL. I LIKE TO LEAVE THE ALTINATOR PULLR FOR LAST BECAUSE IT IS EASIER TO REACH WHEN YOU ARE PULLING ON THE TENSIONER. (WATCH YOUR FINGERS!)
How do you fix a serpentine belt on a Chrysler LeBaron?
you dont fix serpentine belts. you replace them. open hood, although it is easier to reach the belt tensioner from under the car, you will need to route the belt from above. Take the tension off the belt tensioner (a breaker bar or rachet and the proper size socket with a pipe to give ya more leverage should work) and pull the belt while the tensioner is pulled away from the belt. to put new belt on, properly follow accesorie pulleys with new belt, leaving the tensioner pulley last once that far, take your breaker bar or rachet with proper size socket... and pull the tensioner away from the belt so that you can slip the belt over the tensioner, push the belt over pulley. release the tensioner and check to make sure the belt is seated properly on all pulleys. Wahlah
How do you loosen belt on a 97'gmc sonoma?
The belt tensioner, U need a regular size ratchet w/out a socket. Stick the ratchet in the square hole in the belt tensioner , have the ratchet set to lossen and push down. U will see the serpentine belt come free.
Remove serpentine belt 1995 Buick Lesabre?
Use a wrench on the belt tensioner. If there is a square hole, use the socket handle only, if not, use a socket the size of the bolt in the center of the tensioner pulley. Use only enough torque on the tensioner to release tension and slip the belt off of one of the pulleys. (You don't want to loosen the bolt, you only want to move the tensioner.) You did not ask this, but it is important. Pay attention to the routing of the belt. When reinstalling, make sure the grooves are centered and seated on all the pulleys BEFORE slipping the belt over the last pulley. (Of course, using the wrench to move the tensioner.) This can be tricky. You only get one chance, because if you crank the engine with the belt not correctly seated, you will be buying a new belt, and you could get hurt.
How do you change Serpentine belton a 2000 Chevy k2500?
Before removing the belt either draw the belt's path or note the sticker showing the belt's path. Put the correct size socket on the center bolt of the idler tension pulley - pull the tensioner pulley up to loosen the belt - slip the belt off. Install in reverse order. The spring in the tensioner pulley is pretty stout, you might need someone to help you slip the belt back on.
What is a 2003 Dodge Dakota fan belt bolt size?
If you are referring to the tensioner pulley's nut size, it is usually a metric 15mm nut.
How do you get to the belt tensioner on a 2006 town and country?
2006 town n country van 3.3l what is da tool size to release tensioner its not a bolt but a square open
