0
What size socket to remove bolts on the rear wheel hub on a 1992 Saturn?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace Saturn aura headlight bulbs?
Remove the bolts that surround the housing and remove the plastics clips. Remove the clips that attach the wheel well lining and remove the bolts that secure the housing. Pull the bumper away from the vehicle and remove the bulb housing, then remove the bulb assembly and pull the bulb to remove it from the socket. Insert the new bulb and reassemble.
What socket is needed to remove 91 cavalier wheel cylinder bolts looks like reversed torx?
Any type of socket can be used to remove a 91' Cavalier wheel cylinder bolt that looks like a reversed torx. However, make sure the socket is a bolt head socket.
How do you replace rear wheel bearing hub assembly in a 2001 Saturn?
Remove Wheel Remove 2 caliper mounting bolts Slide caliper off rotor Remove rotor Disconnect Brake line Remove 4 mounting bolts Disconnect ABS sensor if any
How do you remove front brake rotors on a 1999 dodge ram 2500?
You have to remove the wheel hub assembly, drive the wheel studs out with a hammer, and flip the assembly over to remove the rotor from the back side.The wheel hub assembly removal requires removing the caliper, 1 11/16 inch nut on the axle shaft, loosening the 4 bolts (14mm 12 point socket) that hold the hub to the knuckle, and hammering on the bolts to loosen the hub. ( use a sacrificial socket to save the bolt heads).You have to remove the wheel hub assembly, drive the wheel studs out with a hammer, and flip the assembly over to remove the rotor from the back side.The wheel hub assembly removal requires removing the caliper, 1 11/16 inch nut on the axle shaft, loosening the 4 bolts (14mm 12 point socket) that hold the hub to the knuckle, and hammering on the bolts to loosen the hub. ( use a sacrificial socket to save the bolt heads).
What type of socket is used to remove bolts in rear wheel cylinder on 91 cavalier?
May only be able to fit in an open end wrench.
How do you replace the water pump on a 1996 Saturn se 1?
To change the pump remove the passenger frt wheel and the front plastic cover. This gives you access. Next remove the belt with a 14 mm wrench on the tensioner, Remove the 3 bolts on the pulley through the wheel well and remove pulley, Remove the 4 10 mm bolts on the bottom of the pump. Next i always remove the washer fluid jug(1 10mm bolt) Install a long extension on the rachet and use a 10mm swivel socket to get the upper 2 bolts out remove the pump and clean the block surface Reverse procedure to install I am trying to replace my water pump and can't seem to find it's location. It's a 1997 Saturn 2L2 Sedan?
How do you change a wheel hub on a Chevrolet optra?
Remove the rear wheel, then the wheel hub should be on four bolts. Remove the bolts and remove the hub. Very easy job.
How do you replace a serpentine tensioner on a 1997 Saturn SC1?
Remove the Right wheel and inner plastic fender which will allow you access to the tensioner side of the motor. There will be a few bolts holding into place on the block. Remove the bolts and remove the entire tensioner assembly. Reverse for replacement.
How do you remove a wheel hub on a 2004 Saturn Vue?
you don't. you buy a new Saturn
How do you change a front wheel bearing on a 1992 Pontiac Bonneville?
The front bearings are sold as a hub/bearing assembly. procedure is pretty simple, remove wheel, brake caliper and rotor, axle nut, and 3 bolts attaching hub asm to spindle. no special tools, except large socket for axle nut, and possibly a torx socket for hub bolts.
How do you Change a rear sprocket raptor?
straithen the lock washers with a flat screwdriver and hammer, take bolts off with a 14mm wrench or socket, remove the wheel, remove the sprocket, put new one in and drive on!
What size socket to remove wheel lock on car?
3.5mm
