0
The vsv is located under the intake manifold, directly over the motor mount. It is pretty hard to get to, but can be changed with the car jacked up off the ground.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Where is the vsv located on a 1999 Toyota Camry?
There are at least two vsvs. One is vsv for evap, and it's next to the air filter. Second one is vsv for egr, which you can find on the backside of the engine.
Where is vsv located on 1992 Toyota Celica?
The vsv is located left top of the fire wall.
Where is the loaction of the Vacuum switching valve 1999 Toyota Camry location?
The VSV is located on the intake manifold side of the emission control valve set.
How do you change VSV for EGR on a 1999 Camry 2.2 liter engine?
I just did VSV for my Toyota Camry today. It is not by the book the way I did is difference After search on-line and bought VSV at Amazon. First take the passenger wheel out after raid you car You will see the VSV is located on the back of the engine under the intake manifold . After several mental try I make the nut wear out so no way I can change the VSV. Finally I decided loose 2 plastic pipes and unplug the connect. Put 2 plastic pipes and plug the connect to new VSV and hang around some where. So I can not finish by the book however I still fix my car and not cost me a fortune. Remember this is a 1999 Toyota Camry and ready for this car to retire
Where is the vacuum switching valve on a Toyota 2000 rav 4?
There are at least 3 of them. VSV for EVAP (2 of them) and one is VSV for EGR. One VSV for EVAP (should somewhere close to the air filter box) and EGR (is attached to the engine on the side facing the firewall, it's not easy to reach it) are located in the engine compartment, and another VSV for EVAP is next to the charcoal canister.
Where is the valve vacuum control on Toyota Camry 1999?
It depends on which of them. On 4 cylinder there are at least 2 of them. One is next next to the air filter box (VSV for EVAP) another one is attached to the charcoal canister which is next the gas tank.
I need to find out why my 2001 Toyota 4 runner will not start after changing fuel pump and vsv. What could it be?
Your 2001 Toyota 4 runner will not start even after changing the VSV and fuel pump because of another mechanical problem. Consider taking it to a mechanic.
How do you replace Vacuum Switching Valve on 98 Camry?
Its under the EGR on the block ya. follow a hose from egr to vsv from underside of car
Diagnose a p0446 code on a 2001 Toyota 4runner the check engine light vsv track and vsv off lights are on at all times you have replaced the gas cap with a Toyota factory gas cap?
INSPECT VSV FOR VAPOR PRESSURE SENSOR (This is the VSV that is located just above the spare tire, next to the charcoal canister.) You will need to remove the spare tire and some vacuum lines in order to access the vsv valve. The VSV cost from the dealer is ~$50-$100. This is the most common VSV to go out, and is the only stocked VSV valve dealership's stock. The p/n is something like ~2460... . If you are going to make the effort to do the following diagnosis I would recommend to just replace the VSV (since it is kind of a pain to get to). It took me ~2 hours to replace, with no book for the first time. 1. Inspect VSV for open circuit.* Using an ohmmeter, check that there is continuity between the terminals.Resistance: At 20°C (68°F): 33 - 39 Ohms* If there is no continuity, replace the VSV.2. Inspect VSV for ground.* Using an ohmmeter, check that there is no continuity between each terminal and the body.* If there is continuity, replace the VSV.3. Inspect VSV operation. View Full Image* Check that the air flows from ports E to P. * Apply battery positive voltage across the terminals.* Check that the air flows from ports E to F.* If operation is not as specified, replace the VSV.3. REINSTALL VSV FOR VAPOR PRESSURE SENSORVSV for EVAP Inspection1. REMOVE VSV for EVAP* Disconnect the connector and 2 EVAP hoses from the VSV for EVAP.* Remove the screw and VSV for EVAP2. INSPECT VSV for EVAP1. Inspect VSV for EVAP for open circuit* Using an ohmmeter, check that there is continuity between the terminals.Resistance: At 20°C (68°F): 30-34 Ohms* If there is no continuity, replace the VSV for EVAP.2. Inspect VSV for EVAP for ground* Using an ohmmeter, check that there is no continuity between each terminal and the body.* If there is continuity, replace the VSV for EVAP.3. Inspect VSV for EVAP operation View Full Image* Check that air does not flow from ports E to F. NOTICE: Never apply more than 93 kPa (0.95 kgf/sq.cm, 13.5 psi) of pressure compressed air to the VSV for EVAP. View Full Image* Apply battery positive voltage across the terminals. * Check that air flows from ports E to F.* If operation is not as specified, replace the VSV for EVAP.3. REINSTALL VSV for EVAP
Where is the vsv located on 2000 Toyota RAV4?
Follow the single air/vacuum tubes, one coming from the side of modulator and the other from the side the of the egr valve (these are disc on top of the engine near the firewall. These two single tubes enter a shaft near the middle of fire wall come out and go under the engine. At the end of them you will find the VSV. It is hard to get at.
When was EC VSV created?
EC VSV was created in 1923.
Where is the EGR valve boost sensor located on 1997 Ford Aspire?
On the firewall next to the EGR vsv.
