0

Search results

Pope John XXIII changed the language of the Mass to the local vernacular.

1 answer


it is a hyndai that's why

it is a hyndai that's why

1 answer


my lights are not working when i changed the pads on my peutgeo partner van

1 answer


changed battery in 2000 chrystler sebring and now will not idle

1 answer


Still have questions?
magnify glass
imp

Vaporization.

1 answer



If you have changed DHCP ip range, the ip address for your router has changed too. You can find your router ip address in your wireless adapter information.

1 answer


It is likely that the crankcase was much too oil. It is likely that the engine would have been damaged if the oil had not be changed.

1 answer


the structure of the federal government

1 answer


NO she she not make quick decisions.

1 answer


Metamorphic Rocks

2 answers


crank sensor or cam sensor

1 answer


changed camshaft and crankshaft sensors in 2005 toyota tacoma 6 clyinder and now it wont start any idea what to try next

1 answer


hello same thing that happend to me i changed my fuel pump, spark plugs,spark plug wires,crank sensor,disturbutor cap and rotary button and still didn't work and still would not start. and the fuel pump would not kick in,until i changed the disturbutor itself. i changed the whole unit. hope this helps p.s my car works fine now it's a 2.5 cirrus v6 1995

1 answer


I have changed the fuel pump on my 1993 Pontic Bonneville, it still is stalling any clues why?

could be Fuel Pressure Regulator

http://www.youtube.com/watch?v=AKtR_yF7bi8&feature=related

1 answer


Changed rocks are called metamorphic rocks. These rocks are formed from pre-existing rocks that have been altered by heat, pressure, or chemical processes within the Earth's crust. Examples include marble, slate, and schist.

2 answers



check your fuse box and relay box.

1 answer


You may have switched the ignition wires when you changed your plugs. I did this once and my kia started, idled terribly, then stalled after trying to drive. Go back and swap the wires that fit on top of your plugs and see what happens.

1 answer




If the radio fuses have been changed on a 1997 Corolla and the radio still does not work, check to make sure the radio is not set to the CD or Tape player mode. It is also possible that the radio is not working because the speakers are not hooked up properly.

1 answer





check to be sure the routing of belt is correct

1 answer


If the head gasket was just changed on the 1996 Toyota Tacoma and now the vehicle won't start it seems that it might be a problem with the computer. Check to make sure all plug ins are good for the electronic parts, then reset the computer.

1 answer


Trouble code P0300 means: Random/multiple cylinder misfire detected

1 answer


when working you must have knocked wire loose for battery termial. i changed the battery ends on my zx2 and missed one wire and spedometer stopped working. found the wire hooked it back up and has never failed since. i hope this helps you with your problem.

1 answer


If you have just changed the battery and you haven't driven car much you need to wait a little while the ECU leans all parameters. In case you drove your car for a while and it's still doing that, erase all codes from the ECU memory.

1 answer


This could be a problem with timing or you need to check the leads to the coil packs are on firmly.

1 answer


Check Owner's Manual. If you do not have one.Check Related links below.

1 answer


you have to reset set the throttle woth scan tool or also known as adaptive relearn

1 answer





You may have damaged an ABS sensor or ABS sensor wiring. Go back and check each wheel.

1 answer


Change crank shaft angle sensor ul get a spark

1 answer


Sounds like you need a new water pump or you could have air in the cooling system

1 answer


I own a 2004 Vette and I recall reading about this problem. I can't recall the info so I

1 answer


looks like you need to bleed your brakes they most likely have air in them and bleeding them should fix this

1 answer


The coil pack you changed for that cyl. may be burning build up in the cyl. and may clear soon, or the coil pack may have been shorted to hide the fact that cyl. was a oil burner, now its live and burning oil once again

1 answer


Not sure what other symptoms are present, but if this problem is accompanied by a smooth idle (normal idle) then it could be a bad speed (RPM) sensor. The RPM sensor is about $75 and is located off the camshaft on most Sebrings - your results may vary! Good luck.

1 answer


check your owners manual if you have one, if not call the dealership and they should be able to tell you.

1 answer


put a 305 in a 95 gmc 1500 now it want start.We put a new fuel pump in and its still want fire.

1 answer


You accidentally disconnected the little black wire that connects to the crossover. it is easy to do. Simply plug it back in and it will work again

1 answer


You may need to do an automated ABS bleed. You'll need a tech2 to do this. You'll have to take it to a shop or a dealership.

1 answer


after changing anything to do with a code it has to be reset drive 100 miles to reset code

1 answer


Information on this site worked on my 2002 GU Patrol

http://forums.nicoclub.com/zerothread/248779

1 answer


it changed by... well it changed... It just changed!

1 answer