0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
When was the first Chevrolet muscle car made?
Given that a typical muscle car has an intermediate body, front engine, rear wheel drive, minimum of four barrel runs at least 155's in the quarter mile, and is an American car, I would say the 1965 SS396 Chevelle (with the Z-16) option.
Which is a better car company Chevrolet or Nissan?
Chevrolet on EVERY THING!!! The only good car on the Nissan company is the Nissan GTR
What is better Chevrolet or Ford?
Chevy is far better than ford in most cars and trucks. The Chevy 2500 HD is better than the ford F 250. CHEVY IS BETTER!!
How do you install Chevy 454 heads?
Cylinder heads are installed on a Chevy 454 big block engine by placing the gasket down on the engine block and positioning the heads over the marking tabs. The bolts are then installed and torqued to specs in sequence.
1968 Chevy 6 cylinder flywheel part 3791021 Will it work on a Chevy 283 or 327?
Yes, it is same flywheel.
Will a ford canopy fit on a Chevy?
It will depend on the trucks 'trim' or model. I.E short-box, extended Cab, ect, and the year to know if it will or will not fit. It wont have to be exact, but very close to.
Please ask a new question and include the year, and bed length
What is the horsepower of a Chevy 4.3 boat motor?
Depends on the year. More than likely somewhere around 190 h.p.
What does engine code p0125 on Chevy malibou mean?
Trouble code P0125 means:Insufficent coolant temperature for closed loop fuel control
How do you remove the heater core on a 57 Chevy?
Drain the coolant. Remove heater blower motor assembly...disconnect wire. Remove hoses from the heater core. Remove the 2 vertical metal "keepers" from each side of the heater core duct by prying them upwards. Also...there might be some screws through the firewall interfering with the metal "keepers" so be sure to check and remove them from inside the vehicle. Carefully remove the duct...it might be stuck with some kind of sealer or gasket. Once the core is exposed remove the screws that hold it to the fire wall and carefully remove it from the car. Installation is pretty much the reverse. Take your time and it should go easy. Oh...check the heater box for straw, hornets nest's and other foreign materials.
Where is the knock sensor located on a 1988 Chevy pickup 1500 5.7 engine?
The knock sensor is located 5inches into the gastral-flux capasitory chamber with a 300degree turn into the left rear chamber which hold the fluids. -Profesor Nicholson Rowe PhD in car mechanics
Why is the abs light on in my Chevy uplander?
The abs light is on because you either have an abs sensor bad or a wiring problem or a hub bearing shot. You will hear a growling noise is you have a bad bearing usually a lower speeds like 40 mph. You may also experience a bit of a vibration from 1 wheel.I hope this helps you.
What is the ignition timing for a 250 6 cylinder Chevrolet engine?
depending on the year 72 and prior 4 to 6 degrees before tdc after 10 degrees before tdc
What is the lug nut size for a 2005 Chevy 1500 4x4?
Probably 3/4" or 13/16". Why not just check with some sockets and see?
see if blows white smoke and look at spark plugs its most likely head gasket out of intake leak
Replace the fuel filter & air filter. If you have never replaced the spark plugs, do so.
How do you replace a Chevy hhr taillight?
Pop the plastic cover in the cargo area near the rear... it's about 8"x3" pull out the foam and move the plastic shield aside. This give you access to the back of the light panel. Turn the socket 1/3 CCW and pull out. Always replace both sides at the same time. If one goes out, the other will go out soon anyway.
How does a small block Chevrolet engine work?
the same way all modern combustion engines work with fuel ,compression, and ignition
What is the limited edition on the Chevrolet SSR?
As far as I know, there are two of them: Signature Series & Final Production Run.
Do 2001 Chevy S-10s use shock absorbers?
yes. all "S" series gm trucks have used shocks on all four corner for the entire time they were produced.
What size motor is in a 2000 Chevy 2500 pick-up?
All 4WD & Long Bed RWD models have the 6.0 L 300 HP V8. Short bed 2WD models have the 5.3L 285 HP V8.
How do you reset service engine soon light 1990 Chevrolet 1500 4x4 5.7l?
You put your "gear stick" into the exaust pipe and throttle your "gear stick" a couple of times and the car should kick back into life
How many 1959 2 door Chevy Brookwoods were made?
20,760 two door station wagons were made by Chevy in 1959
Set the timing at 6 degrees BTDC (Before Top Dead Center). Make sure you pull the vacuum line off the distributor and plug the line with a golf tee or something before setting the timing, it will make a difference and it's the recommended procedure. Be sure to reconnect the vacuum line after you time it . Just fyi check the timing again to see how much the vacuum advance changes the timing, but trust the way you set it with the line plugged, the specs call for the line to be plugged. While you are at it , rev the engine and watch to see if the timing is advancing properly. You can get a timing tape to put on the vibration dampener. You should get well over 30 degrees total advance depending on how much is built into that particular dist . A good speed shop can curve the dist to optimize your application. It's one of the cheapest most effective and most overlooked performance mods you can make. Don't see the timing advance then that is your problem. If you still have the hard starting, stalling, and idle problem, then it is not cause by timing. Check all vacuum hoses and replace any that are cracked or leaking. In fact I would just replace them all to make sure.
