Chevrolet

Chevy makes more brand name vechiles and they are a better company and the best type of vechile.

Try checking your spark plugs & wires. Can also be caused by dirty fuel filter.

Head bolts ------------------------------ 65 lb/ft Intake Manifold (Cast iron heads) -- 30 lb/ft Exhaust Manifold ----------------------- 25 lb/ft Valve Cover ------------------------------ 3 lb/ft

202 refers to the intake valve size, as in 2.02 inches, upgrading to 202 heads is a very common way to gain horsepower, but usually requires upgrading the intake (better intake manifold and a better carb) and installing headers, to make the most of it. even installing a new highperformance camshaft

The speed limiter is programmed into the computer, when you exceed a preset limit, such as 97 mph. It is programmed into the PCM based on the speed rating of the stock tires. To change it you will have to buy a power programmer or performance tuner, available from several different manufacturers for around $400. You can't remove it, but you can raise it to a certain extent, based on the speed rating of your tires. There is no way you can bypass it, since the PCM (Powertrain Control Module) must have speed information to process engine parameters. The power programmers are set up so that you must buy a programmer for each vehicle. You can't borrow one from a buddy. The PCM has a unique id number programmed into it. The best way I can explain it, it removes the factory programming from your PCM, stores it, and then reprograms it with your modified program. You must restore the original programming that is stored in the performance programmer to the vehicle re-programmed before you can use the programmer on another vehicle.

Chevrolet got its name from the founder, Louis Chevrolet, a race car drive.

Ever try a steering arm puller?

Since a 1990 truck has fuel injection, this will be a difficult and expensive task. Everything one the top of the engine will need to be replaced. If it has a throttle body instead of individual injectors the intake manifold, distributor and wiring will all have to be replaced. You will need to decide on what distributor will be used. My suggestion is to come up with another plan unless you have plenty of time and money.

Yes.

smell of antifreeze and no visable leaks usually indicates that the heater core needs replacing

there should be a sticker under the hood that will tell you this, or in your service manual, if still no luck, you will need a chiltons, or haynes mannual.

Math is used to measure how to put the right shaped parts in the cars.
They multiply the flat rate time to do a job by the hourly rate, then double it for an estimate.

It is located behind the distributor.

The Hanger bearing has to be pressed off and then back on

There are several websites that help decode Chevrolet VIN. These can be found through any search engine. The decoders provide information and description about the vehicle whose VIN is entered.

The IAT on a 2006 Chevy HHR is part of the MAF sensor. You will find the IAT located on the large air box under the hood of the Chevy HHR.

Chevy 350 bored 60 over.

....

not the best way to come to a 358... The "NASCAR" way is to use a 400sbc block and a 327sbc crank. High revving and big hp up top.

Without knowing the exact model the exact weight cannot be determined. However, a 1998 ChevyÊtypically weighs between 5,100-5,500 pounds.

Normally from 4 to 4.5 quarts. Park on level surface. Drain the oil and change the filter. Add 4 quarts. Start the engine and run for a minimum of 1 minute. Shut it off and wait 1 hour. Check the oil level and add as necessary. You now know the capacity.

According to the Edmunds (commercial) website (refer to the link, below): "In 1911, after William C. Durant had been ousted from General Motors, he joined forces with Swiss-born racecar driver Louis Chevrolet to found the Chevrolet Motor Car Company. The company's first offering was the Classic Six."

Remove the covers from your 1997 Chevrolet rear speakers. Remove the speaker retaining screws. Remove the wiring harness from the back of the speakers. Reverse the process to install the new speakers.

I do not know the capacity. Put in 4 quarts. Let it idle for a minute, then check the dip stick. Keep adding until it reads full. DO NOT OVERFILL!!!

Remove dust cap in the center of front hub

Remove the nut (2) and the washer (3) from the hub.

The four bolts on the back side of the hub do need to come out. Usually a good 15mm socket on a breaker bar will break them loose with no problem. Continue applying heat and penetrating oil. They will eventually break loose. It usually works better to use a breaker bar instead of air tools.

Drain the fuel from your 1990 Chevrolet C 1500 gas tank. Remove the fuel line. Remove the fuel pump retaining plate screws. Remove the fuel pump. Reverse the process to install the new fuel pump.

It could be a broken belt on front tires it could also be broken eng mount.need more info.markstang.