Airsoft Guns and Accessories

sa quiapo may official store ng mga original airsofts at bb's yung mga airsoft nila doon original kaya lahaat ng airsoft ko dun ko binibili.\

saan pala specific na lugar s quiapo po sir un bilihan at phone number?...

yes and no. RGP international sells plastic balls 4.5mm's across of the highest quality, they are meant for industrial oil drill bearings and such and so are very durable and come in high and low densities, the equivalent of .12 and .20 density. These will not however work in any airsoft guns.

This all depends on the laws that are in your state. You will want to check the laws before you even purchase an airsoft gun. For the most part though, having an airsoft gun shouldn't be a big deal. If you have uptight neighbors however, you may want to check with them (If you are using loud guns).

Since many companies make both of these types of airsoft guns, you must specify the make and model, or a proper comparison can not be made.

The more powerful the batter just means the longer your gun will last before it has to be recharged. 'Fox Airsoft Store' offers some gun upgrades, these will improve your gun. Also, a gun's fps is already pre-determined by what parts are installed, upgrades will improve the gun but stronger batteries will only extend the gun's life before it needs to be charged.

Depends on what type of gun it is. Spring is in around $90. Electric is in the $150's. Gas is around $200.

Try two hours and see what happens.

All depends on 2 things: how much fps the airsoft gun has and how thick the armor is 200- fps wont feel like anything higher up 400-600 fps might feel like a bee sting or less depending on the thickness of the armor

You can`t. The gun is well done, only problem is the air compression part, that is:

1) plastic, that is a really weak point

2) the metal roll on the spring need more room than the plastic air compression has, so the impact WILL destroy the gun very soon.

And by soon i mean like no more that 10 shots. Mine broke after 5 BBs.... So if you can, sell it as long as it works, because later you`ll be sitting on it forever.

The magazine is not meant to be taken apart and will likely shatter plastic if you try this

well where I live in Canada if a airsoft/co2 BB gun goes over 500fps you must register it as a lethal weapon so I assume it is 500fps for you too.

What to do

How to use a gas gun: Remove the magazine from the pistol by pushing on the magazine release. With the magazine removed: Fill the magazine, with the magazine below the gas canister As illustrated:
Make sure the can is ALSO upside down. Make sure they are both perfectly in line and completely vertical. Do not tilt sideways at all or angle the green gas canister and the gun magazine. Make sure the nozzles get a firm seal, and proceed to fill the "Liquid" into the mag by pressing firmly down with the airsoft gas canister. Filling time depends on the mag capacity. A normal handgun mag is generally about 3 seconds. A 50-round mag is usually about 5-6 seconds. This will insure you get a full charge of gas, for the amount of BBs.

After loading the green gas into the magazine, load the BB's. Simply pull down on the magazine follower and insert BB's as illustrated below Next, simply reinsert the magazine into the gun. After the gas has been loaded, magazine has been loaded with BBs, simply cock the gun as shown below and you're set to go:




What NOT TO DO when filling the mag:
If you fill the mag, and gas begins to spill, STOP. Let the magazine warm up at room temperature before attempting again. This is usually about 5-6 minutes. If you are able to form a tight seal and fill correctly, allow the magazine to warm to room temperature. Tapping the big metal button on the top, rear side of the mag will discharge the GAS from the gun magazine. Do NOT do this! It will prematurely wear out the seals and also cause the O-rings to freeze, damaging them permanently. Instead, fire the gun until out of gas. This is the safe way to discharge a gas-gun.

Fire the gun in WARM weather. Using during the cold seasons are not advised. They will not cycle completely, fire well, and will use more gas than normal. Rapid-firing of the gas-gun will also cause the gun to freeze up, resulting in damage to the magazine or gun. These problems are not as prone during the hotter seasons or warmer weather.

Use HIGH grade BBs for your guns. Lower quality BBs will tend to jam in the magazine well, preventing proper firing. Marui, Excel, Airsoft Elite, or AirSplat BBs are are highly recommended. These are all models which we carry, Airsoft BB. Using .12 is not advised for higher end airsoft guns, such as electric or gas will VOID THE WARRANTY and may cause permanent damage.

Gas-gun care: Be sure to keep your slide and all moving parts lubricated with SILICONE oil which can be purchased on our website or at your local hardware store. Do not use anything else, such as petroleum based lubricants. ONLY 100% pure silicone oil is required. Other lubricants are not safe for use on plastic and rubber parts.
Do not use Hoppes #9, WD-40, and other petroleum based lubricants will damage the guns permanently.

Be sure to also spray silicone oil into the top nozzle of the magazine well every 5-6 magazines uses. This is done, by pressing the top release valve on the the mag while putting a quick spray of silicone into the top rubber exhaust valve. This will keep the seals and O-Rings properly lubed for a lifetime of use. For more details illustrations on how to maintain your gun, please refer to our Maintenance Guide.

Recommended gases for gas airsoft guns:

KWC: use HFC 22 or Green Gas only for these guns. Use with Red Gas will void the warranty

KSC/KWA: use HFC134a gas unless equipped with a metal slide. If equipped with metal slide upgrade use HFC 22 or Green Gas. Use with Red Gas will void warranty.

Western Arms: HFC 134a gas is recommended. Use with any other gases (such as HFC22 or Green Gas) with void warranty.

KJW, Y&P, STTI, HFC, other Taiwanese guns: HFC22 or Green Gas is recommended. Using HFC134a is not powerful enough. Use with Red Gas will void warranty.

Maruzen, Marui: HFC 134a gas is recommended<. Use with any other gases (such as HFC22 or Green Gas) with void warranty.

Marushin: HFC 134a gas is recommended. Use with any other gases (such as HFC22 or Green Gas) with void warranty.

Tanaka: HFC 134a gas is recommended. Use with any other gases (such as HFC22 or Green Gas) with void warranty.

Storing your gas-gun magazines: After usage please leave or insert a small amount of the appropriate gas, enough for 2 - 3 shots is recommended. Do not keep them in storage while fully charged or completely empty. This will allow the O-Rings of the magazine properly lubricated while in storage.

First you must take into account the laws of the country you are passing into, if they are illegal there than you can't take it over. As for getting through customs with an Airsoft gun, you must notify customs that you have a replica gun. Google it to find out more.

There is only one way to be seriously hurt with an airsoft gun, and that is to be shot directly in the eye. As long as you wear a face mask, the worst you can get is a welt or at close ranges you could bleed a bit, but you won't ever get hurt badly unless you do something stupid.

You can play airsoft at a local airsoft store if it has a field and you are alloud to play, but my recomendation is to just play airsoft in some woods, any kind of woods, as long as it doesn't break the laws.lol

i have seen a clear, see though airsoft gun but that's all on amazon!!!

http://www.amazon.com/UHC-inch-revolver-Clear-airsoft/dp/B001PH7OBK/ref=sr_1_12?ie=UTF8&s=sporting-goods&qid=1242470836&sr=1-12

You shoot people.

You must pry off the slide with a knife or some other object, ( pry from the back of the slide). Then there will be a silver pin you

must pop out,( its very easy to push out). Next unscrew the safety on the right side of the gun. Lift up from the barrel and its open.

Spring guns require you to cock for every shot, they usually are cheaper(unless it it a high quality bolt action), they can be more durable than AEG's. An electric AEG will be able to fire full auto and usually has a higher cap mag. Also, AEGs usually have metal gearboxes called MPEG airsoft guns. Lower quality AEGs with plastic gearboxes called LPEGs are lower quality and break easier as well as having lower fps and other performance. I have had an LPEG and the mag misfed, and it tore up the internals. With my new gun linked below i have had no problems, the only upgrade i have used is a 600 rd hi cap mag. My gun chronoed at 496 fps right out of the box with a .28 bb. With standard .2 bbs ive clocked over 500 fps and hit targets in 1 inch groups from 400 feet without a scope.

Spring guns are mostly pistols, although i use a Mauser co2 pistol now.

(((web site address redacted)))

Final answer:

AEGS-Good, but more expensive and can be fragile

Springers- great for beginners, but not something i would regard as anything more than a cheap sidearm.

yes they can i have had many hits from airsoft guns that have broken skin but they where from arenas and shot from higher FPS guns but normally they don't.

A systema PTW with the highest power cylinder has 700 fps, and a highly modded sniper can have higher than 800 fps so yes, there is a such thing as a 750 fps gun, but it would probably cost you about 2,000 and a lot of time to install all the mods necessary. (I'm guessing you would start with the most powerful gas sniper you can find, put the longest, tightest bore barrel you can find in it, replace all the gas parts with extremely strong parts that allow for high flow, and possibly use CO2 instead of green gas for higher pressure)

I am looking for the same grips as you, let me know if you find a source.

-------

The Wards Western Field model 5 is the same as the (Sears) JC Higgins model 85, both of which are the MAPF (La Manufacture d'Armes des Pyrénées Françaises, later Manufacture des Pyrénées - Hendaye) Unique model D2, also known as Le Corsair, which entered production in the mid-1950s. The model D came in varying barrel lengths and were named D1 through D6, depending on barrel length. Unique went out of business about 2005.

Parts can be obtained from Numrich and Bob's Gun Shop , and replacement grips specifically from Vintage Gun Grips . And, of course, parts show up on the usual firearms auction sites, Gunbroker and Auction Arms, and sometimes on eBay (there are no firearms on eBay, but gun parts are sold on it).

Check under all three names -- sellers do not always list all available parts under all the names.

In Canada any "gun" that shoots a projectile at 500 FPS or more is considered a firearm.

There are many Airsoft (soft pellet gun) competitions around the world. Enter the words "airsoft competition" without the quotes into your favorite web search engine to find competitions around the world; add the name of your city, state, and/or country to narrow it down to your locale. You might also consult your nearest Airsoft dealer for addresses of Airsoft clubs and other relevant information.

If you are talking about feeding problems, make sure you are using .20 gram Precision BB's ONLY. If the motor isn't overturning, your battery is dead, or there is a problem with the motor. Try taking it to your local airsoft shop NOT A SPORTING GOODS STORE.