0
Dodge Caliber
Introduced in 2006 (for the 2007 model year), the compact Dodge Caliber replaced the Dodge Neon. During the summer of 2012, the Caliber will be replaced by the 2013 Dodge Dart. Questions about the Dodge Caliber can be asked here.
433 Questions
How do you check transmission fluid in 2007 Dodge Caliber?
The dipstick is a special tool that only the dealer has.
How do you check transmission fluid level in automatic 2007 dodge caliber sxt?
The dipstick is a special tool that only the dealer has.
The fuse location for the rear windshield wiper on a 2007 dodge caliber?
Fuse number for rear wiper dodge caliber 07
Does the dodge caliber have grease fittings?
Not likely, as most vehicles today have sealed grease fittings. Take a look and see.
Location of oil sending unit a 2007 dodge caliber?
It is on the front of the engine, under the intake manifold and behind the ac compressor. either the intake or ac has to be removed to access.
Where is the thermostat located and how to change a 2007 Dodge Caliber SXT?
There are two thermostats in the plastic housing on the driver side of the cylinder head. It needs removed to access them. Replace all seals, fill coolant, and warm up engine.
Where is the thermostat on a 2009 2.4 caliber?
The Dodge Caliber 2.4L has two thermostats. They are in the plastic housing on the driver side end of the cylinder head.
How do you reset oil change on dodge caliber?
Turn key to on position depress the acceleration pedal slowly three times then turn car off...
Where is the inertia switch on a dodge caliber?
Dodge does not use inertia/reset switches.
Dodge does not use inertia/reset switches.
Where are the grease fittings on the 2007 dodge caliber?
There where none from the factory.
There where none from the factory.
Where is the thermostat located on 2008 dodge caliber sxt?
There are actually two thermostats. They are in and under the large black plastic housing bolted to the driver side end of the cylinder head.
There are actually two thermostats. They are in and under the large black plastic housing bolted to the driver side end of the cylinder head.
Where do you add transmission fluid in a 2008 dodge caliber?
Actually, as it states in the manual, you have to take the car into the dealer to check the transmission fluid. It has a lock that only the dealer can unlock for the dipstick to pull out.
What automatic transmission will interchange with a 2009 dodge caliber with a 2.4 engine?
Only the CVT that was used in the Calibers and Jeep Compass/Patriot.
How do you reset change oil maintenance light on a 2008 Dodge Caliber?
Turn on Ignition - depress gas pedal 3 times
How do you replace the air filter on a 1995 Villager?
There is no cabin air filter on a 1995 Villager.
How do you change a brake light on a 2007 dodge caliber?
2007 Dodge Caliber bulb replacement: Purchase the correct replacement bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
How do you replace Dodge Caliber air filter?
Locate the air filter case. In a 2007 Dodge Caliber, it is located on the right-hand side of the engine compartment.
Unlatch the four latches located on the air filter cleaner compartment. Pop open the compartment and pull out the old air filter cleaner.Slide in the new air filter. Latch the air filter cleaner compartment. You have just replaced your car's air filter.
- Step 4
Read more: How to Change an Air Filter on a 2007 Dodge Caliber | eHow.com http://www.ehow.com/how_6057163_change-filter-2007-dodge-caliber.html#ixzz0w7S8rcGJ
How do you set when next oil change is due on 2010 dodge caliber?
You cant set oil change times, the vehicle is programmed to tell you when to change it according to your driving habits, to reset your oil life monitor...turn key to start position, wait 3-5 secs for lights to turn off on dash, depress the gas pedal 3 times with in 10 seconds...turn key off and you're done :)
