0
Dodge Caliber
Introduced in 2006 (for the 2007 model year), the compact Dodge Caliber replaced the Dodge Neon. During the summer of 2012, the Caliber will be replaced by the 2013 Dodge Dart. Questions about the Dodge Caliber can be asked here.
433 Questions
What oil type synthetic or regular oil in a 2010 Dodge Caliber 2.0 L?
You can use either conventional or synthetic, your choice.
For what model years did Dodge produce the Caliber SRT4?
The Dodge Caliber SRT4 was produced for the model years of 2006 through 2009. It was introduced in February 2006 at the Chicago Automobile Show. The Caliber SRT4 was a hatchback.
How do you change a wiper on a dodge caliber?
As of the 2011 model year, all dodge calibers have the most common hook-end wiper arms. See sources and related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.
How do you remove a stuck brake caliper from a 2008 dodge caliber?
stuck? how is it stuck? if you have removed all (4) bolts then it should slide off.. if not push hard on the caliber to depress the cylinder making it easier to slide off
Where is the thermostat on a 2006 Dodge Caliber?
There are two thermostats. They are in the plastic housing on the driver side end of the cylinder head.
Where is reset button for tire pressure dodge caliber?
There isn't one. If all pressures are set at the spec on the label on the drivers door jamb, the vehicle has been driver over 10 miles, and the light is still on there is a sensor failure.
No, it should come on solid for about 5 seconds and then go out if the system is ok.
What size wiper blades will fit a 2009 Dodge Caliber?
24" drivers side, 17" passenger side and a special 10" rear wiper blade. The rear is tough to find - checkout link below. The front wipers will be a little easier to find however do not buy by size alone - lookup your vehicle by make, model and year and make sure to purchase the correct part numbers that not only are the correct length, but also the correct wiper arm attachment.
How do you reset the change oil light on a 2009 dodge caliber?
Turn ignition on with engine off. Press gas pedal to the floor three times in 5 seconds. Cycle key and light should be reset
Turn ignition on with engine off. Press gas pedal to the floor three times in 5 seconds. Cycle key and light should be reset
What is the gas mileage on the Dodge Caliber?
I own a 2007 Caliber R/T. automatic.2.4L engine. I am getting 23.5- 24.2 mpg According to the EPA, the Dodge Caliber does 21 - 24 mpg in the city and 24 - 29 on the highway, depending on its engine.
How do you brighten dashboard lights on a Dodge Caliber?
Simple. Just install this http://dodgecaliberinstrumentclusterlight.blogspot.com/2014/06/repairing-dodge-caliber-dash-lights.html
Where is the blower resistor located on a 2007 dodge caliber?
It's in the bottom of the blower motor, on the side of it. You can look by taking the door down on the glove box or it may be below that. It is where you need to look though.
Where is the thermostat located on a 2009 dodge caliber?
There are two under the plastic housing on the driver side end of the cylinder head.
There are two under the plastic housing on the driver side end of the cylinder head.
Where is the horn relay fuse for Dodge Caliber?
The horn relay fuse for the Dodge Caliber is located in the fuse box under the hood. You can find the fuse box near the battery on the driver's side. The specific fuse and relay layout can be found in the owner's manual, which provides details on identifying the correct fuse for the horn. Always ensure the vehicle is off before checking or replacing fuses.
Can you flat tow a 2007 Dodge Caliber fwd?
Yes, you can flat tow a 2007 Dodge Caliber FWD, but it requires specific precautions. The vehicle's owner's manual may provide guidelines on how to properly prepare the car for flat towing, which typically includes ensuring the transmission is in neutral and the ignition is in the "ACC" position. It's also advisable to use a tow dolly or consult with a professional for best practices to avoid potential damage to the vehicle's drivetrain.
