0
Dodge Charger
The Charger is a mid-size car manufactured by Chrysler for its Dodge brand. This model has been produced in different platforms and has been offered in different body styles like sedan, hatchback and luxury coupe.
1,832 Questions
Where can you find a wiring diagram for a 86 dodge ram-charger?
try a chiltons repair manual from the library.
How much horsepower does a Dodge charger superbee have?
the new one has 425 and the old super bee could be had with a 383 with 335 horse or the 440 with 375 or the hemi with 425 under rated horse.
Can you install a mygig into a 2007 dodge charger sxt?
google lockpick v2 adaptoer. The company makes a kit but need to look at their site to see if your vehicle is compatible
Where to put transmission fluid in a 2006 charger?
There is a metal fill tube at the back of the engine on the passenger's side. It has a cap on it that has to be unscrewed like a bottle cap, to remove. The car has no dipstick and must be checked for proper level at the dealer. However, once you have done that, you can use a funnel and fill it from the previously mentioned tube.
How do you unlock a 2006 charger if the keys are locked in?
Short of shattering a window, might need to call a locksmith
How do jump start a dodge charger?
There should be a positive battery cable hook-up under the hood and take the ground on the cables and hook to engine block or some metal piece.
i have a 98 v6 es, it sounds good on take off, but i wouldn't race it. the fuel shuts down around 127mph. i think the rev limit is around 6500 or 7000 rpm, the auto trans was hot i guess and it did not shift normally. i had been running it at 120-125 for about an hour.
AnswerNOT FAST AT ALL,THEY JUST LOOK NICE, AND VERY NOISY WHILE DRIVING AnswerNot true I have an 99 avenger it's pretty quick it's just the acceleration isn't that great but once it kicks into second it's good what avenger are you looking into? The new ones go with the awd r/t model that's the best one out. If your looking at the older ones go with an v6 es model. Mines only a v4 base model which is decently fast. Put it this way if you like eclipse you'll like the older v4 avengers they have the same moter in them.ANSWER
I have a 95 Avenger ES 6cyl 2.5L,...I've had it up to 230 km/h which equals about 140 MPH.
Will charger rims fit a 1994 f150?
I doubt they will fit but if you have a charger rim try it on your ford and see.
Is the bolt pattern on a dodge charger the same as a dodge magnum?
It should be as they are both the same platform.
What is the base engine size of the 2010 Dodge Charger?
The 2010 Dodge Charger has a 2.7 L base engine size.
Could you revise the question to let us know where the sound is coming from? Under the hood, under the car, from the exhaust, etc? That info would help in the diagnosis-from-afar.
Why won't my dodge charger change into any gears?
either the shifter cable needs adjusted or the transmission has gone out.
Where is the 1 plug wire on distributor of dodge 383?
On the 383 Dodge , # 1 on the distributor cap faces to the front and slightly towards the passenger side
How do you install a glove box cover 1969 dodge charger?
To install a glove box cover on a 1969 Dodge Charger, first, ensure the glove box is empty. Align the cover with the hinges at the top and secure it in place using the provided screws or clips. Make sure the latch mechanism is functioning properly before closing the glove box. Finally, check to ensure that the cover opens and closes smoothly.
Is the torque for a 2008 dodge charger with a siemens sensor 58 inch pounds?
Technician Asays the torque on a 2008 Dodge Charger with Siemens
sensor is 58 in—lbs- Technician B says the torque on a 2008 Dodge Charger
with Schrader sensor is 71 in-lbs- Who is correct?
How do you remove ignition switch form 1966 dodge charger?
To remove the ignition switch from a 1966 Dodge Charger, first disconnect the battery to ensure safety. Then, remove the steering column cover by unscrewing the screws that hold it in place. Once exposed, locate the ignition switch, disconnect the wiring harness, and unscrew the switch from the column. Finally, gently pull the ignition switch out of its housing.
