0
Jeep
Jeep, a subsidiary of Chrysler Group, Limited Liability Company. Jeep specializes in manufacturing and selling sport utility vehicles and is the oldest SUV-producing brand. Jeep was founded in 1941.
2,017 Questions
Can a 1972 cj5 body fit onto a 1980 cj5 frame?
The answewr is NO. Up to and including 1975 they were considered short nose frames and from 1976 thru 1980 they were long nose frames. hope this Intel is of any use. if i can share any more info contact me at: rokcrawlcj@hotmail.com
How do I repair a Jeep error code 121?
There are a few reasons for a Jeep error code 121. Some of the causes are a bad connection with the TPS, a corroded sensor, or a harness is rubbing a harness.
What is the fuel mileage for a jeep 4.0?
My 2000 4.0 liter automatic usually gets around 15 or 16 mpg with combined highway/city driving. It's also got 30x9.5x15 tires.
Where are spark plugs located on a 6 cylinder jeep renegade?
On the right side or the left side of the head.
you can go to the dealership and get the video that came from the factory. watch it. it will explain a lot about how your jeep works and proper care. instructions should also be included in your owners manual in the o.d. khaki case in the glove box. you can also go to the jeep dealership and they will give you a demonstration. its really an easy process but you need an extra person or two to help you remove the hard top without breaking it due to its flimsiness.
How much to replace an jeep oil pan?
The cost to replace a jeep oil pan is around $700 including labor. You can choose to do it yourself for about half the cost.
Can a vacuum leak cause braking problems in a jeep yj?
On a vehicle equipped with power brakes the answer is yes. The P/B booster works on vacuum, so if the leak were severe enough it would make the brake pedal be very hard to push. Other than that, as vacuum leak would have no effect on braking.
What is the normal oil pressure reading for a jeep 5.2 engine?
Running at operating temperature around 40 psi.
How do you reset security alarm 2005 jeep limited when key in door or transmitter doesn't work?
With all of the doors locked, LOCK the vehicle with the key in the drivers side door.
How does the idler pulley look on a jeep motor?
In an Inline 6 Jeep engine, the idler pulley is located to the right of the A/C pulley. It is a smooth pulley, not a grooved one.
Rough shift 1st to 2nd gear 08 jeep jk manual?
This is a 2008 vehicle that is still under warranty. Let the dealer deal with this. You paid for the warranty, use it.
What causes Engine knock jeep?
Engine knock happens when an unbalanced air and fuel combination occurs inside of an engine cylinder. If the problem is not corrected the vehicle runs the risk of having a piston malfunction.
How do you replace a broken parking brake release lever on a 91 Jeep?
I believe tyhere was a recall on this. check with dealer
What is the operating temperature for 2004 Jeep 4.0L engine?
The operating temperature for a 2004 Jeep with a 4.0 liter engine is between 180 and 210 degrees. The optimum temperature would be about 200 degrees (Fahrenheit).
How do you check fuel pressure on a jeep yj 2.5?
On the side of the throttle body where the fuel feel line and the fuel return line go in there is another spot for a hose to go in this is for the fuel pressure gauge you must hook a fuel like into this then to your Gage fuel pressure at idle should be 14-16 psi.
What is the weight of a jeep CJ7?
If the 6th digit of the VIN is an A, it weighs 3750 lbs. If the 6th digit of the VIN is an E, it weighs 4150 lbs. This is only the GVW - it is not the actual weight of the vehicle. Shipping Weight is usually listed at 3000 lbs, experience says that you need to take the vehicle to a set of scales to know the actual weight. Scales can be found at truck stops and may be listed under "public scales" in the phone book. 3100 lbs is typical, but that will vary based on engine and options.
What are causes of steering wobble on power assisted power steering?
the allignment from the tires, or the frontend of the car needs to be adjusted.
Sometimes low power steering fluid can cause this but more likely if you are aligned properly and/or it is not all the time wobbling at same speeds it can mean that your power steering pump is taking in air. To check for this have someone in the car while running. Have them turn the wheel all the way to the left and all the way to the right. Listen for belt slippage/squeal if none watch during this process with power steering cap off and see if any bubbles appear. The ONLY way for there to be bubbles in this tank is
a. Recently or still very low power steering fluid levels (you may hear a sucking noise if this is the case)
b. somewhere on the low pressure/suction line there is a weak seal, loose connection, or break in the line.
If power steering levels are good (check cap and see what type of fluid to fill with as the two options of power steering fluid can cause major problems if mixed or the wrong one is used it will be either power steering fluid or ATF [automatic transmission fluid]) then the next step is to replace the clamps on the rubber hosing check manual for details specific to your make/model/year Visually inspect for what appears to be loosest. There may also be a crack either in the rubber on the conecting side or somewhere along the hose visually inspect for crack. beyond this replace all rubber lines and clamps related to the suction side. If issue persists you may consider replacing the power steering pump.
How do you get a torx bolt out of a jeep?
Many auto repair shops like advance auto, autozone, pep boys... etc have torx bits either in the form of a screwdriver with the torx bit on the end or as a socket for your socket wrench. On the funnier side.... just pick it up! Here's your sign.
How do you change O2 sensors on a 95 Jeep YJ 4.0L?
FIRST MAKE SURE YOU ONLY PURCHASE THE REPLACEMENT O2 SENSORS FROM YOUR LOCAL JEEP DEALER. DO NOT PURCHASE AFTERMARKET O2 SENSORS FROM AUTOZONE,ADVANCE AUTO PARTS, MAIN,NAPA OR ANY PLACE OTHER THAN A DEALERSHIP PARTS COUNTER. UNLESS YOU WANT TO DO THE JOB AGAIN IN ABOUT 2-4 WEEKS. YOU WILL ALSO NEED A SPECIALTY TOOL WHICH I WOULD RECOMMEND THAT YOU PURCHASE AT ONE OF THE AFTERMARKETS SHOPS AS IT MOST LIKLY WILL NOT GET A LOT OF USE FROM THE AVERAGE PERSON. IT LOOKS LIKE A DEEPWELL SOCKET, WITH A LARGE SECTION CUT OUT ON ONE SIDE FOR THE WIRES ON THE O2 SENSORS TO STICK OUT. YOU SIMPLY DISCONNECT THE SENSORS WIRE HARNESS, THE LOOSEN THE SENSOR. REPLACE WITH NEW SENSOR, RECONNECT HARNESS. YOU MAY SMELL A HOT TYPE ODOR THE FIRST TIME OR TWO THAT YOU DRIVE AFTER REPLACING THE SENSOR.
How do you remove an ignitionswitch from a 2002 jeep cheroke?
Slide hammer. Be sure to disable the alarm first and always check the parking lot for cameras and rent-a-cops.
Well this is a tricky answer... The two front fenders will fit on the DJ5. Obviously you can't install any kind of fender flares on the rear wheel wells due to the sliding doors. As for the grill, the DJ5 had 5 grill slots and the CJ5 has the signature 7 grill slots. I would imagine that it will fit no matter the side that the steering wheel is located because the entire engine compartment was designed for left or right side drive. Look at any CJ 5, 7 or 8... there are areas on the firewall that can be "punched" for that very reason.
What is the name of the part that the oil filter screws onto on a 1995 jeep 4.0 l engine?
oil filter housing
How do you remove the ignition switch on Jeep CJ7 1981?
hey, if you mean the the little cylinder thing in your colum, i am working and stuck on that at the moment, you have to pull your steering wheel off, take your blinker etc stuff out, then there are like 5 little holes and in the bottom of one of them there is a screw, you have to take that out and then the cylinder should pull out
