0
John Deere
John Deere is the leading manufacturer of agricultural machinery in the world. Questions about John Deere products and their proper operation can be asked here.
2,566 Questions
What is grain capacity for 8300 john deere grain drill?
Filled to maximum capacity, it's approximately 36 bushels of wheat.
Where do you check the hydraulic fluid level john deere 4310 tractor?
To check the hydraulic fluid level on a John Deere 4310 tractor, locate the hydraulic fluid reservoir, which is typically found near the rear of the tractor. Remove the cap from the reservoir and use the dipstick, if equipped, to check the fluid level. The fluid should be within the recommended range marked on the dipstick or the reservoir. Ensure the tractor is on a level surface and that the engine is turned off during this process for an accurate reading.
How do you reset the oil change indicator on your John Deere 125 lawn mower?
To reset the oil change indicator on a John Deere 125 lawn mower, first ensure the engine is off and the key is removed. Then, turn the ignition key to the "Run" position without starting the engine. Press and hold the hour meter button (usually located on the dashboard) until the oil change indicator resets. Finally, turn the key back to the "Off" position.
What battery will replace john deere LVA 15187 battery?
The John Deere LVA 15187 battery can typically be replaced with a compatible equivalent such as the John Deere TY25829 or a similar group size battery, depending on the specific application and equipment. It's essential to verify the specifications, including voltage and dimensions, to ensure proper fit and performance. Consulting the equipment's manual or a local dealer can provide guidance on the best replacement option.
How do you Replace Clutch On John Deere Model M?
To replace the clutch on a John Deere Model M, start by disconnecting the battery and removing the necessary components to access the clutch assembly, such as the hood and the flywheel cover. Next, remove the clutch release lever and the retaining bolts holding the clutch in place. Carefully take out the old clutch and replace it with the new one, ensuring proper alignment. Finally, reassemble the components, reconnect the battery, and test the clutch to ensure it operates smoothly.
Do you have to bleed john deere 3720 fuel lines?
Yes, bleeding the fuel lines on a John Deere 3720 may be necessary after servicing the fuel system, such as replacing the fuel filter or running out of fuel. This process ensures that air is removed from the lines, allowing the engine to receive a proper fuel supply. Typically, you can bleed the lines by using the manual fuel pump or by loosening the fuel line fittings at the injectors until fuel flows without air bubbles. Always refer to the operator's manual for specific instructions related to your model.
Why won't John Deere mower blades engage?
If John Deere mower blades won't engage, it could be due to several issues. Common reasons include a faulty electrical connection, a blown fuse, or a malfunctioning safety switch that prevents the blades from engaging. Additionally, a worn or damaged belt that connects the engine to the blades may be the culprit. Checking these components can help diagnose and resolve the issue.
How to route the belt on the blower attachment of a John Deere 425 lawn tractor?
You can route the belt on the blower attachment of a John Deere 425 lawn tractor by first mounting a 90 degree gearbox .
How do you change drive belt on a John Deere 345?
To change the drive belt on a John Deere 345, first, ensure the engine is off and disconnect the spark plug for safety. Remove the mower deck by detaching it from the tractor, then locate the drive belt. Remove the old belt by releasing the tension from the belt tensioner, and install the new belt by routing it according to the diagram typically found on the mower deck or in the owner's manual. Finally, reattach the mower deck and reconnect the spark plug before testing the setup.
Where is the brake safety switch located on a john deere 1995 lx178?
I believe it is threaded into the transaxle at the rear of the mower
Where is engine filter on 450 john deere dozer?
On a John Deere 450 dozer, the engine air filter is typically located on the side of the engine compartment. It is housed within a rectangular or cylindrical air cleaner assembly, which may be easily accessible for maintenance. To find it, look for a large, often metal, canister that connects to the intake manifold. Be sure to consult the operator's manual for specific details and maintenance procedures.
How do you change a oil filter on a john deere b?
To change the oil filter on a John Deere B, first, ensure the engine is cool and secure the tractor on a flat surface. Locate the oil filter, typically found near the engine, and use an oil filter wrench to unscrew it. Before installing the new filter, apply a bit of clean oil to the rubber gasket on the new filter, then screw it on by hand until snug. Finally, refill the engine oil if necessary and run the engine briefly to check for leaks.
Do John Deere Riding mowers have a low oil switch?
Yes, many John Deere riding mowers are equipped with a low oil pressure switch as a safety feature. This switch helps prevent engine damage by shutting down the mower if oil pressure drops below a certain level. However, the presence of this feature may vary by model, so it's always best to consult the owner's manual for specific details regarding a particular mower model.
How do you remove pto electric clutch?
To remove a PTO electric clutch, first, disconnect the battery to ensure safety. Next, remove any protective covers and the drive belt to access the clutch. Use a socket or wrench to unbolt the clutch from its mounting, and gently pull it off the shaft. If needed, you may have to remove any retaining pins or clips before fully detaching the clutch.
What champion spark plug is for john deere 345?
The recommended Champion spark plug for a John Deere 345 lawn tractor is the Champion RJ19LM. This spark plug is designed to provide optimal performance and efficiency for the engine used in this model. It's important to ensure proper gap settings and maintenance for the best results. Always consult the owner's manual for specific recommendations.
What year john deere 111h serial number moo111h262061?
The John Deere 111H with the serial number M00111H262061 was manufactured in 1985. The "M" at the beginning of the serial number indicates that it is a model 111H, and the numbers following it help identify the specific unit and its production year.
Can john deere hy-gard and low viscosity hy-gard be mixed?
Yes, John Deere Hy-Gard and Low Viscosity Hy-Gard can be mixed, as both are designed to meet similar specifications for John Deere equipment. However, it's essential to check the equipment's requirements to ensure optimal performance. Mixing different fluid types may affect the viscosity and performance characteristics, so it's always best to use the recommended fluid for your specific application.
What is the weight of a john deere 618c 12 row 20 inch cornhead with chopper?
The John Deere 618C 12-row 20-inch corn head with chopper typically weighs around 1,600 to 1,800 pounds. This weight can vary slightly depending on specific configurations and attachments. For precise specifications, it's advisable to refer to the manufacturer's documentation.
