0
John Deere
John Deere is the leading manufacturer of agricultural machinery in the world. Questions about John Deere products and their proper operation can be asked here.
2,566 Questions
If the snow is very wet this will surely clog the auger, if the belt is loose that drives the auger this will surely clog as well. This will happen especially to a single stage snow blower as they strain a lot more then a two stage thrower in wet snow conditions. It helps to spray Pam in to the housing before use, a nice coat, like a cake pan!
Why does the center blade spin on my mower deck and the outer ones don't?
Its yours how should we know?
Which John Deere accessories have toy counterparts?
For the best information pertaining to toy counterparts, visit your local John Deere store. For more technical information and several items to choose from, visit the official John Deere website.
Does john deere charge a restocking charge for items returned?
This question really has a variant of answers. It depends on your John Deere dealer. Some will charge a restocking fee on items, especially parts, to cover the cost of returning those unused parts. Some won't charge for return parts, so you just need to contact your dealer.
Where are John Deere manufacturing plants?
John Deere has dozens of factories all over the world. Places include the USA, Mexico, South America, Russia,
What is the value of a John Deere GT275 tractor?
i bought one recently for $700,000 i bought one recently for $700,000
Which tractor is bigger a 4850 John Deere or a 8100 John Deere?
The 4850 has more HP, 180-190. The 8100 has around 160 or so.
Since lift lever is not engaging the mower deck on your John Deere LT155 how do you reconnect?
I just fixed a similar problem on my LT155. All that needed to be done was to tighten the button on top of the lift lever by screwing it in until it stops. This puts pressure back on the spring under the button, which is necessary to push down on the latch at the other end of the lift lever so that it will engage the keeper on the tractor frame. Without enough pressure from the spring under the handle, the latch won't engage the keeper. Very simple fix, actually. (Once you figure out what's wrong.)
what are some of the tools John Deere employees use to work on the assemble line.
Where are the john deere 4045hf275 electronic-controlled rotary injection pump timing marks?
there are two marks.. one in the pump itself.. and another in the flywheel. you stand up in the side of the fuel pump to find the flywheel mark.. there are two holes,,, one of about 1 inch diameter and a smaller one of 3/8 inch.... sometimes there isa plastic cork that covers the bigger hole and is attached to the smaller hole... remove it completely... insert a bolt or a screwdriver in the smaller hole..don't pay attention to the bigger one... then with a socket or a wrench turn the damper clockwise until you find the hole in the flywheel.. now you go to the fuel pump that of course is not installed yet..with an allen key, you proceed to open a plug that is located a little lower from the fuel return line... once you remove the plug, turn the pump's rotor until you find inside the hole, a flat surface.. that's the mark ... there is a special tool to keep it in place.. or you can use a bolt that fits properly inside there..... then you install the pump and that's it
How do you change the auger belt on John Deere TRS32 snow-thrower?
You have to remove the black belt cover between the engine & shoot held on with 2 bolts.
Next you will need to separate the auger housing from the unit.
This is done by removing the 2 bolts just below the black belt cover
now you have access to both the drive & auger belt.
Upon resembling make sure when the 2 units go back together that you have the notices on both sides on the bottom of the unit together.
How much does a john deere 7760 cotton picker weigh-?
The weight of the John Deere 7760 cotton picker is 69660 lb/pounds.
What is the fuel consumption of a John Deere 544K wheel loader?
The fuel consumption of a John Deere 544K wheel loader typically ranges from about 3 to 5 gallons per hour, depending on the operating conditions, load, and usage patterns. Factors such as terrain, attachment use, and operator efficiency can also influence fuel efficiency. For precise figures, it's advisable to consult the operator's manual or contact a John Deere dealer for specific applications.
How do you remove a PTO on stx 38 John Deere lawnmower?
Unplug the connector wire. Take the tensioner spring loose for the deck belts, then slip the belts off of the pulleys in the front of the mower right below the engine. There is a single 5/8" bolt than comes out vertically on the bottom of the pto clutch. Take that bolt out and make sure the 2 belts are slipped off of the pulleys and the pto clutch should drop right down. Make sure and remember how the spacers and the square slip pin goes in the pulley assembly above the pto clutch. Install back in the reverse that you removed it. P.S. It also helps give you more room to work if you lower the mower deck all the way "down".
What is the life span of a John Deere X740 riding mower in a commercial area?
the life span of the x740 riding mover in a commercialized area is 16ft precisely. {nerd snorts and pushes up his glasses}.
John Deere farm tractors are built in Waterloo, Iowa, USA. Any one else know more about Case or AGCO?
The gas cap says 50:1 right on it.......commonsense would suggest if that escapes anybody, they should be kept well away from power tools............
Where Can you See A Belt diagram for John Deere RX 75?
It depends on which belt you speak of, but I answer on another forum and put up a number of belt diagrams including many Deere ones. See link.
Yes, John Deere was a real live person born in 1804 in Rutland, Vermont. He eventually started the modern company Deere & Company after his plows started to go into mass production. For more info about him see the related link...
