0
Locks and Latches
Locks and latches are parts of a door. While the latch ensures that the door stays in a closed position to prevent it from opening, lock prevents the door from being opened without a matching key.
2,075 Questions
Why will your key not turn if it is in park also the steering wheel Will Not Lock at all?
The key cylinder has failed.
How do you pick lock washermachine coin boxes?
It depends on the lock.
There's not enough information here to answer the question.
Suffice it to say, "If you have to ask this question, you can't do it."
First, spin the dial clockwise a few times to reset the lock. Then continue turning clockwise until you reach the first number of the combination. Then spin the dial counter-clockwise one full revolution so you are back at the first number. Then continue turning counter-clockwise until you reach the second number. Then turn the dial clockwise until you get to the third number (do not spin the extra revolution this time). At this point, you should be able to pull the lock open.
provide information that can assist in illegal activity.
Alternate Answer: Picking locks is not illegal. Much like firing a rifle, the intent and the result determines its legality.
To pick a lock, you'll need at least two tools. The first is a tension wrench, sometimes called a Torsion Wrench. This is the bar that goes into the base of the lock. The second tool is the pick, which generally come in three basic types:
Hook - a long, thin pick shaped like a hook at the end.
Snake (Ball in some cases) - Has gentle curves at the end to make the rods fall in place
Diamond - Is triangulated for those rods that require a more precise pressure.
Essentially the tension wrench is used to apply pressure to the lock by turning it in the direction the key normally would turn. The pick is then inserted over the top of the tension wrench and the rods are "raked" (move the pick in and out while applying gentle upward pressure) until all the rods click into place. The tension wrench should then be able to turn the lock.
Note: This is the basic principal. The actual execution of the task is a very different matter.
It's easy to apply too much tension to the lock.
It's uncommon but possible to apply not enough pressure.
It's easy to over-set a pin, and since there are 5 of them in a fairly tight space, good luck figuring out which one, two, or more you've over-set.
It's also easy to under-set a pin, and again since there are 5 pins (perhaps more) in a tight space, God be with you to figure out which one (or more) it is.
This is the actual skill of the locksmith, and no amount of books, videos, or watching someone will teach these things.
This requires "feel" on the part of the locksmith, which can only be gained through experience.
What do you do if your key breaks in the lock?
I usually punch the door a few times and swear a lot.
But seriously, I've had great success with a set of needle-nose pliers. If that doesn't work, try a power drill with a steel-cutting bit. The down-side of that is that whatever the lock was on is going to be unlocked until you can get a new lock. If It's the lock on your toolbox... Borrow a set of pliers or a drill from your friend.
What are the shocks called that holds open your trunk?
Trunk props,or prop rods.
They are "gas struts"
How do you reset Samsonite travel sentry 3-digit lock?
From the samonsite website faq's
Set / Reset 3-dial combination lock
How do I set / reset my Samsonite or American Tourister 3-dial combination lock?
Setting Your Samsonite or American Tourister 3-dial Combination Lock:
1. Remove the red packing arrow on the lock if your case has one.
2. The case is set to 0-0-0 at the factory. Choose your own 3 digits which you can easily recall (birthday, address, etc.).
3. Locate the button or lever adjacent to the dials:
-If there is a button, push it towards the dial and hold while you rotate the dials to your desired setting, then release the button.
- If there is a lever, move the lever to its lower position (some move to the right and up), rotate the dials to your desired setting, then return the lever to its original position.
Your combination is now set to your 3-digit code.
Where can you get a latch for your Contico pick up Tool box?
At the Contico web site they state that you can get keys and parts for their aluminum or metal tool boxes at Tradesman Truck Accessories - 1-866-789-5300.
If you are looking for a latch for one of their plastic tool boxes, call 1-800-831-7077.
How much does it cost to change a front door lock?
300 dollars
ANS 2 - Anyone can change a front door lock themselves with a Multi screwdriver and reasonable mechanical ability. -I've fitted hundreds of locks and the one thing they all have in common is very good instructions. Even someone who has never done anything like this before could change an existing lock in an hour or so. Front door locks cost from 30 or so to over $ 150.
Most locksmiths I know charge almost $ 100 per hour and some even a 'callout fee' on top of that.
How do you reset a combination lock?
It depends on the type of lock. Some can't. Need to know manufacturer to answer the question. Type of combination lock.
How do you pick an American tourister suitcase lock?
start at 000 got to 001 and so on moving on up from the last number
How do you open a master lock?
You open your lock by using your lock combination or if it has a key hole, put a key inside.
- TO OPEN- Turn RIGHT 3 times. Stop at the 1st number.
- Turn LEFT one full turn passing the 1st number to stop at the 2nd number.
- Turn RIGHT and stop at the 3rd number. Pull the shackle.
Example: If your numbers were 31, 12, & 2.
You would turn right 3 times and stop at 31.
Then you would turn left one full time, passing 31, and stopping at 12.
Finally, you turn right from 12 and stop at 2, then pull the shackle.
Reset Sphero lock combination?
Sphero locks cannot be reset - only resettable locks can be reset. The Sphero locks come with a permanent combo.
How do you get to the hood release mechanism when the latch is broken?
The generic answer would be to first take a good look on the hood release mechanism on a similar car. Then get a good flashlight, look through the grille and see if there's a way of accessing the latch from there.
My car door won't close and its because the latch is stuck and i can't get it out..how do i fix it?
Have you tryed to put a screwdriver in the "hole" where the door striker would go and as you pull the handle up push the screwdriver out. As if you were going throught the motions of the door opening but the screwdriver acts as the striker.
How do you unlock an anti-theft steering wheel lock when the key does not work?
Hold the steering wheel tightly and move it quickly counter clockwise. This movement should unlock it.
get a axe and hit it at the code an it will crack
A lock that is not mastered will only work with one key. By adding small pins in the lock cylinder it can be made to use two keys. The second key is a master key. By adding different sizes of these small pins to the cylinders of locks with different keys they can all be made to work with this master key. For a full explanation go to http://home.howstuffworks.com/home-improvement/household-safety/security/question710.htm
Where can you find a sample letter to request additional payments to be put towards principal?
You can find sample letters at places such as the LoveToKnow website. The letter should be used only as a form.
