0
Mitsubishi Endeavor
The Mitsubishi Endeavor is a mid-size crossover sport utility vehicle produced from 2004 to the present. Based on the Mitsubishi PS platform, the car features a 3.8 L SOHC 24v V6 engine and a 4-speed semi-automatic transmission.
308 Questions
How do you change transmission fluid 2004 Mitsubishi Endeaver?
You can't change all the fluid without special equipment. Take it to a transmission shop.
How much oil do you use for an oil change on a 2005 mistubishi endeavor?
Oil + Filter = 4.3 Liters or 4.5 Quarts
Why does my MITSUBISHI ENDEAVOR air conditioner blow out hot air?
You may have one of two problems,1) Your A/C system is low on 134a Freon charge. or 2) the connecting high pressure switch is not making good contact. I would check nu. 2 first because if the compressor is not coming on at all it's going to blow hot air but the A/C indicator light will still be on. If it's low on charge, the light will blink off and on.
In the above case, AC is likely to give out air at the same temperature without any cooling or heating.
However if the AC starts giving hot air into your room in cooling mode than the problem could be in the radiator cooling. Reason could be choking of the radiator cooling coils which blow hot air out from the back of your AC. This generally happens if the external part of your room AC is situated around potential choking materials lying loose such as waste, birds feathers etc. The radiator fan sucks such loose material into the radiator coils which get choked, resulting in back-flow of hot air of the radiator into your room. It also adversely affects the cooling cycle as the gas does not get cooled adequately, in the radiator.
Read more: http://wiki.answers.com/Your_air_conditioner_blows_hot_air#ixzz1Tm3ma6fv
That could be hard to find the answer to. What I would do, is wait until your gas light comes on, fill a gas canister with a gallon of fuel, keep sealed in your trunk. Stay near gas stations, bus drive around until you run out of gas, than put the one gallon of gas in your tank, and drive to a gas station A.S.A.P. Then you will always know.
How do you remove Mitsubishi Endeavor dome lights?
To remove the dome lights in a Mitsubishi Endeavor, first ensure the vehicle is turned off and the light switch is in the "off" position. Use a flathead screwdriver or a trim removal tool to gently pry off the light cover. Once the cover is removed, you can access the bulb; twist it counterclockwise to remove it from the socket. If necessary, replace the bulb and reattach the cover by pressing it back into place.
How do you reprogram the stereo on a Mitsubishi endeavor 2004?
To reprogram the stereo on a 2004 Mitsubishi Endeavor, first, turn on the vehicle and the stereo. If you're looking to reset it, press and hold the "Power" button and "Station" buttons simultaneously for about 5-10 seconds until the display resets. For pairing Bluetooth or setting radio presets, refer to the owner's manual for specific instructions, as the process may vary slightly based on the stereo model. Always ensure the vehicle is in park while performing these actions for safety.
Where are the sparkplugs in a 06 Mitsubishi endeavor?
In a 2006 Mitsubishi Endeavor, the spark plugs are located on the engine, accessible by removing the engine cover and the ignition coils. The Endeavor is equipped with a V6 engine, so there are six spark plugs, one for each cylinder. Each spark plug is situated on the top of the engine, connected to the ignition coil, which needs to be removed to access the plugs for replacement or inspection.
What causes water on floor board of a 2004 Mitsubishi endeavor?
Water on the floorboards of a 2004 Mitsubishi Endeavor can be caused by several issues, including a clogged or damaged sunroof drain, which allows rainwater to overflow into the cabin. Another common cause is a failing door or window seal, leading to water leakage during rain. Additionally, a malfunctioning heater core can leak coolant, resulting in moisture on the floor. It’s important to diagnose the source accurately to prevent ongoing damage.
How do you replace wiper motor on Mitsubishi endeavor?
To replace the wiper motor on a Mitsubishi Endeavor, first, disconnect the battery to ensure safety. Remove the wiper arms by loosening the nuts and gently pulling them off the shafts. Next, take off the interior cowl panel to access the wiper motor, which is usually secured by bolts. Disconnect the motor's wiring harness, remove the bolts, and install the new motor by securing it with bolts, reconnecting the wiring, and reassembling the cowl and wiper arms.
Where is the air conditioner firewall on Mitsubishi endeavor?
The air conditioner firewall on a Mitsubishi Endeavor is typically located in the engine compartment, separating the engine area from the cabin. It is usually situated behind the dashboard and can be accessed by removing certain interior panels. For specific location details or repair guidance, it's advisable to consult the vehicle's service manual or a professional mechanic.
How do you replace console light for shifter on a 2006 endeavor?
To replace the console light for the shifter on a 2006 Endeavor, first, disconnect the vehicle's battery to ensure safety. Next, remove the console cover by carefully prying it up with a trim removal tool, taking care not to damage any clips. Locate the bulb holder for the shifter light, remove the old bulb, and replace it with a new one. Finally, reassemble the console cover and reconnect the battery.
How do you program fob for 2001 Mitsubishi eclipse?
To program a key fob for a 2001 Mitsubishi Eclipse, begin by getting into the vehicle and closing all doors. Insert the key into the ignition and turn it to the "On" position without starting the engine, then turn it back to "Off." Repeat this process five times, ending in the "On" position, which will trigger the door locks to cycle, indicating the vehicle is in programming mode. Within 30 seconds, press the lock button on the key fob to program it; you should see the locks cycle again to confirm successful programming.
How do you remove the air intake on a Mitsubishi endeavor?
To remove the air intake on a Mitsubishi Endeavor, first, ensure the engine is cool and disconnect the negative battery terminal. Next, remove any clamps or screws securing the air intake duct to the throttle body and air filter housing. Carefully detach the intake hose from both ends, and if applicable, disconnect any sensors or hoses attached to the intake. Finally, lift the air intake assembly out of the engine bay.
How do you unplug battery cables in a Mitsubishi endeavor?
To unplug the battery cables in a Mitsubishi Endeavor, first ensure the vehicle is turned off and the keys are removed from the ignition. Using a wrench, loosen the nut on the negative battery terminal (usually marked with a minus sign) and carefully lift the cable off the terminal. Repeat the process for the positive terminal (marked with a plus sign). Always disconnect the negative terminal first to minimize the risk of a short circuit.
How do you reset abs light on 2005 mitsubishi endeavor?
The ABS light is on because there is a problem with the ABS system. Until that problem is fixed the light will remain on. Once the problem is fixed the light will reset itself after a short drive.
How do I install roof rack cross bar on Mitsubishi Endeavor?
Slide the end covers on rear straight back. Install cross bars. Slide cover back on. Easy Thanks - I found out that you need a "pin" to release the front and rear end covers. I used a center punch as the pin in the small circular hole on each cover. After that, it really was easy!
