0
Power Tools
Power tools come in a large variety. This category covers drilling machines, angle grinders, hand held planers and band saws, impact wrenches, cordless screw drivers, electric chisels, jackhammers, etc.
930 Questions
Amazoncom How often must fire drill's conducted on mobile offshore drilling unit's?
CFR 122.524Fire fighting drills and training.
(a) The master shall conduct sufficient fire drills to make sure that each crew member is familiar with his or her duties in case of a fire.
(b) A fire drill must be conducted at least once each month.
(c) Each fire drill must include:
(1) Summoning passengers on a vessel on an overnight voyage to areas of refuge or embarkation stations;
(2) Summoning the crew to report to assigned stations and to prepare for and demonstrate assigned duties; and
(3) Instructions in the use and location of fire alarms, extinguishers, and any other fire fighting equipment on board.
(d) Each fire drill must, as far as practicable, be conducted as if there were an actual emergency.
(e) Fire fighting drills and training shall be logged or otherwise documented for review by the Coast Guard upon request. The drill entry shall include the following information:
(1) Date of the drill and training; and
(2) General discription of the drill scenario and training topics.
How do you change belts on Black and Decker vacaum cleaners?
You remove the base plate under the roller and slide the main b eater out. Replace the belt and main beater together.
How are many circular saw motors rated instead of using a horse power rating?
Circular saws are rated for blade size and their motors are rated by 'service amps' .
Can you use your own power tools at work?
That depends where you work. But why would you want to wear out your tools when they probably supply them.
What determines the size of a portable belt sander?
The width of the rollers and distance they are apart.
What is a radial arm saw used for?
For cutting a variety of straight or angled cuts at varied depths.
Why do electrical power tools have only two wires?
The better quality tools all have 3 wires. You are looking at cheaper tools.
What is the price of a 1957 Black and Decker Electric Drill?
I bought one last night 4/9/13 at auction for $8.00.
What are the sharpest saws made of?
The sharpest handsaws are made of highly tempered steel. The sharpest power saw blades are carbide tipped.
How do you keep sandpaper from walking off belt sander when running?
There is usually an adjustment knob on one of the rollers, often the front one. This angles the roller slightly and keeps belt straight.
Should you buy tools for your contractor?
Any decent contractor should already have to tools he needs, or have factored them into the estimate. If a contractor starts asking you for new tools to do this or do that, I would be concerned that he didn't know what the job was when he bid for it. That would be like a mechanic asking you to buy him a ratchet because he never realized that a ratchet could be useful. But if you added on to the job after the initial estimate, and new tools are required for the new work you need done, then maybe you should either consider it an expense or bring in a second contractor to do that part of the job.
What is better 12volt drill or a 18 volt drill?
Depends on it's usage. An 18 is more powerful and will drill more holes or drive more screws, but is quite heavy to use if for instance you are working on a ladder or drilling upwards. In those case a lighter 12 is better.
What tools are needed to make hydroelectric power?
Normally, hydroelectric power requires a dam and a turbine. It is possible to use a water mill instead of a dam.
Did power tools increase productivity?
Yes, power tools especially increased productivity in home-building.
How do you fix a homelite chain saw?
That depends entirely on what's wrong with it. If you have no knowledge of this fairly complicated machine, you should take it to a 'small engine and lawn mower' repair shop.
How do you remove drill bit from hilti drill?
You press the holding ring toward the body of the drill and slightly twist and pull the bit away from the chuck.
Can you use a normal drill instead of a Core drill?
That would depend on what you were drilling and what the project is.
