0
How much should a clutch job cost on a 1995 Isuzu Pickup 5 speed wt 2.3L - 4 Cylinder engine?
Wiki User
∙ 14y ago
Normally a Clutch job for a Mechanic to do it will cost you around $500 to $700 depending on there labor rate... The parts are about $100 to $150...
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
The clutch on a 1988 Jeep Cherokee Chief won't disengage should the hydraulic master cylinder be replaced?
did you check your slave cylinder? is the hydraulic master cylinder leaking? did you try bleeding the clutch at all? what exactly does your pedal do? does it go straight to the floor or does it have pedal? there may be an air pocket in your lines? it could be alot of things you have to be more specific with your question
How do you secure a fender guitar pickup?
make sure all the screws are on the faceplate right and it should be
What other parts need replaced when you change the ac compressor and clutch on a 1994 Jeep Grand Cherokee Limited with a 4.0 liter engine?
Any time system is opened it will need to be evacuated prior to charging Also accumulator/drier should be changed at the same time
What causes a 1999 Jeep Cherokee to start vibrating only when the AC is on after the AC blew cold air then warm air before a pop was heard?
Check the belt and pulleys. Make sure the AC pulley turns. When the AC is turned on, the clutch should engage to the pulley and the AC compressor should turn, and yes, it can cause the engine to vibrate a little. If the clutch doesn't try to engage, there could be some problems with the AC, but first try to find out what caused the noise, and determine if the AC compressor is turning.
How do you get your 99 Chevy s10 4x4 to roll start?
If it's automatic, you can't. If it's standard shift, hopefully you are parked facing down hill or you have a couple buddies that can push you. Get in the vehicle, turn ignition on, hold the brake, push in the clutch and put the truck in second or third gear. Continue to hold the clutch down and release the brake and allow vehicle to roll down a grade. Once you have reached 5 to 10 mph, let the clutch up. The engine should turn over. Weather it starts or not depends on what was wrong in the first place.
How do you know when the clutch master cylinder is gone in a 1995 escort?
Whenever you are having a problem with the clutch disengaging the engine from the transmission it is advisable to bleed the clutch slave cylinder. If the clutch can't be operated by bleeding the slave cylinder then the clutch master cylinder is gone and should be replaced.
Where is the clutch bleeder valve on a 1983 Nissan 720 pickup?
It should be down below where the slave cylinder connects to the tranny
Where is Toyota sr5 clutch master cylinder located?
The clutch master cylinder should be attached to the firewall, nearest the drivers side, inline with the clutch pedal. In the engine compartment, look for a smaller version of the brake fluid reservior.
Should you replace your clutch master cylinder when replacing clutch?
At least the slave cylinder. The clutch master cylinder can be replaced at any time.
How do you install a slave clutch cylinder for a 1994 Honda civic ex v-tech?
The slave clutch cylinder on a 1994 Honda Civic is located inside the engine compartment. On the driver-side close the firewall. The clutch fluid should be drained. Remove the mounting bolts and clutch lines to replace the slave clutch cylinder.
Where does the little rod go in a 1990 Mitsubishi pickup just replaced the clutch and forgot the rod?
If you just replaced the clutch and pressure plate, the only "little rod" I can think of is in the slave cylinder. It is what pushes the fork in to disengage the clutch. If you did not put it in, you should not be able to shift or engage the clutch. The slave cylinder should blow out the seal when you step on the clutch pedal. The rod is about the diameter of a pencil and 2 inches long more or less?
How do you know if the clutch cylinder on a 97 suzuki sidekick is bad and it is not the clutch?
After you have located the clutch slave cylinder, have someone depress the clutch pedal. You should see the piston of the slave cylinder extend somewhat. If it does not, either the slave cylinder is bad, or the master cylinder, or, there is not enough brake fluid in the system for it to operate properly. Check the level in the master cylinder. If the slave cylinder is leaking profusely, it is probably bad.
Where is the clutch bleeder valve on a 1993 Saturn sl2?
It SHOULD be on the clutch slave cylinder. Follow the hydraulic line from the clutch master cylinder down to the slave cylinder. Depending on the vehicle, it could be behind the dust cover of the bell housing.
Where is the slave cylinder on a Mitsubishi mighty max?
Mine is a cable clutch so there is no slave cylinder. But if yours is a hydraulic clutch then it should be located on the firewall on the driver side close to the master cylinder.
How to remove Clutch slave cylinder S10?
the slave clutch cylinder is located inside the housing of the clutch/transmission. Unless you really know what you are doing a trained tech probably should replace this part.
Where would you check the Tran fluid level in a 1995 Honda Accord since the clutch is going to the floor?
Its not your transmission fluid. If you have a clutch it is probably going bad. You can check your clutch master cylinder fluid in the engine compartment. It is just like your brake master cylinder. Chiltons has repair manuals at the library I think. Or the manual in your car should show you where it is.
How do you test slave cylinder?
step on the clutch and hold it to the floor clutch should stay disengaged for as long as you hold it down
