How do you replace the turn signal windshield wiper cruise control arm on a 1987 Olds Ciera?
This is not easy since the cruise cont wires go down through the steering column. I suggest you take it to the garage.
What needs to be done to remove and replace the combination turn signal cruise control wiper and headlight dimmer switch on a 2000 Silverado?
The combination turn signal, cruise control, windshield wiper, and headlight dimmer switch simply plugs in. Pull the relay switch out and replace with the new switch. Read More
The signal lights, the high/low beams, the cruise control, the wipers, the wiper delay function, the windshield washer and the 4-way flashers. Read More
This means that the switch is going bad. You will need to replace the switch that is on your steering wheel or on the turn signal switch. Read More
It's the the turn signal switch that controls the Cruise Control Assembly. Therefore any problem to the Turn Signal switch affects the whole road safety. Read More
The blinkers are stuck on my 95 avenger your brights wont come on either can you tell you what the problem may be?
Check the Multi switch. This is the turn signal on the side of your steering wheel. This is sometimes called a multi switch because it runs the signals, headlight dimmer, sometimes cruise control and windshield wipers. Easy to replace. Read More
To use the cruise control on the PT Cruiser, turn the cruise control on in the steering wheel. Accelerate to the desired speed and push in the end of the left turn signal knob. The cruise control should then control the speed. To take the car out of cruise control, a person can tap the brake. Read More
grip it firmly and pull it straight out,new one pushes back in. Read More
on the end of the turn signal lever Read More
How do you replace the turn signal switch on my Oldsmobile cutlass supreme 1996 We checked the fuses and they are good wipers do not work nor does the cruise control?
On the 94 and 95 you just pull it out. Be careful with the wiring connector. Read More
on the turn signal lever it is a small slide switch Read More
Does the electronic signal from the vehicle speed sensor go to the computer under dash then to cruise control and speedometer?
No Read More
It may be a safety feature on your car. If you are going to make a turn you for sure do not want the cruise to be engaged. Read More
Yes. You need two parts, the cruise control module (with associated wiring and cable) and a new signal lever - left/right turn and windshield wiper controls (with associated wiring) - that has the cruise control on the end. The cruise control mounts in the engine compartment and plugs into the existing wiring. The old signal lever is swapped out. I purchased the parts on eBay (seller: S10WAREHOUSE, who provided great service and I felt reasonable… Read More
On the turn signal "switch" there is a button on the end that you push to engage, then to the left of the windshield wiper settings is a switch you can move left or right, moving it left will disengage the cruise control moving it right will increase the speed by about 1-2 mph every time you move it. http://img810.imageshack.us/i/652420224529ad892f.jpg/ This is a picture to make it easier in case I gave a bad description. Read More
sounds like a fuse is blown Read More
What is the correct name for a part that controls the wipers cruise control and turn signals on a car?
I think they call that the "control module" or equvilent. Usually, if you ask for a wiper, turn signal or cruise module, you'll get the one that controls all three. Read More
The 1985 S10 Blazer GMAC Êoffers a delay wiper on the black cruise control lever. ÊThe part number is AM-64109149. Read More
How do you replace a turn signal and windshield wiper assembly on a 1998 Ford F150 4x4 4.2 LT with AC?
Take it to a Ford Dealer. Read More
if it doesn't have cruise control just twist the base of it bottom toward the dash and it will pull out putting a new one in is the reverse if it has cruise control then i suggest you get a haynes or a chilton manual for the illustrated version to make it easier to do Read More
It's on the combined turn-signal/cruise control/light switch lever on the left-hand side of the steering column. If you don't have an owner's manual, a GM dealer should be able to order one for you. You might also find them on eBay or Amazon.com. Read More
All modern vehicles have a VSS sensor (Vehicle Speed Sensor) attached to the transmission or an axle that generates a speed signal. This signal is used by the speedometer, cruise control, and some of the engine and transmission computers. Read More
1997 Lumina. Hazard lights cruise control blinkers tail lights work. Brake lights do not. Replaced activating switch and turn signal switch bulbs fuse checked for corrosion and broken wires. Pls help?
To replace turn signal control module requires removing steering wheel. Took mine to a dealer - $245 out the door. Brake lights work great now. Read More
On the turn signal lever, slide the cruise control switch to on with thumb(there are 3 possitions here, off, on, reset slide in that order). Drive up to the desired speed and press the signal lever on the center with your index finger, this will set the speed. When safe, release pedal and feel for reaction from the car itself. The Camaro will slow down slightly but will almost immediately regain speed if the cruise… Read More
The windshield wiper SWITCH ? It's on the turn signal lever Read More
Do you have to replace the whole unit if the cruise control and delayed wipers do not work and the right turn signal has to be held in order to work?
No. These are all three different controllers working three different devices. But the steering column would have to be dismantled to repair any one or all three of these controls. Read More
I just had a good reliable shop diagnose my cruise issue. Turned out the cruise was fine but the vehicle speed sensor was damaged and wasn't relaying any signal to the cruise system. It runs off the transmission and was around $100 plus time plus diagnosis time. 1993 Explorer 4x4 5spd XLT. Read More
If memory serves, there isn't one. All that switching is done at the turn signal/low highbeam/cruise control stalk. Read More
grab turn signal lever firmly push it in while turning it to left t then pull in same motion Read More
The turn signal switch is located on the left side of the steering column just behind the steering wheel. It also controls Headlights, Hi/Lo beam and cruise control. Read More
The cruise control switch should be on the turn signal control arm. There is a three position switch; off, on and resume are the three positions; "off" to your left, "resume" to the right and "on" in the center when you are sitting in the drivers seat looking at the switch. The switch needs to be in the on position and when you reach the speed you wish to "cruise" push and briefly hold in… Read More
The speed sensor on my 1994 Dodge Ram 2500 was on top of the differential housing on the back axle, the big bell housing between the rear wheels. It's held in a rubber housing which takes a bit of work to remove. If you're asking about this because the speedo/cruise control has stopped working, it might be the speed unit or it might be the there's a break in the wire. If you replace the… Read More
The Multi-function switch( turn signals,hazard,lo/hi beam,cruise control,windshield wipers/washer) has deteriorated inside and one of the thin metal contacts has worn out or come loose. Replacing this assembly should fix you up. The service manual for the 1999 says to remove the air bag ,steering wheel and ignition switch to perform this operation, however I did change the one in my Suburban without removing any of this. You can buy an aftermarket switch for less than… Read More
My cruise control signal comes on the dash when I turn it on but when I set the speed button nothing happens. Why? The increase speed with the switch on the steering wheel does not work either. You need to hagve the system checked for trouble codes to know what the possible causes could be. Read More
The multi-function switch inside the steering column has the turn signal lever and hazard lights button extending outside of the steering column it operates - turn signals - flash to pass - high beam headlights - windshield wipers ( on/off ) and intermittent speed settings for the wipers - windshield washer fluid squirter button Read More
Multifunction switches are located in the steering column. It's the turn signal, cruise control, headlights, wiper, etc lever. In different vehicles they have different functions. Read More
How do you replace a turn signal lamp control module for a Audi 2001 A6 Quattro The lights all work when i turn on my hazards just when i use the swithch there is nothing. They blink once then turn?
you need to replace the hazard light switch the turn signal control module is built in the hazard switch.just had same problem a few months ago. Read More
Will the same turn signal switch from a 1995 Grand Am V6 with cruise control work on a 1995 Grand Am Quad 4 SE with cruise control?
i am about 98 percent sure they will.... 1995 to 1998 grand am's had very similar electrical and engine composition. so i would imagine that it would work fine. the fun part is putting everything in Read More
4 way flasher switch on top of the steering colum is what I have found better known as the turn signal, wiper, cruise control. Read More
This is for a '95 and similar vintage vehicles: Check to see if the speedometer also fluctualtes, it may be minimal and not obvious. The speed sensor is on the transmission, accessible from the right side. If it is starting to go, any drop in signal will cancel the cruise control settings and the car will suddenly decelerate as though you killed it. A reset at speed will hold as long as the speed sensor… Read More
Yes. Mazda part numbers: w/Cruise Control BR75-66-120D w/o Cruise Control BR72-66-120G w/o Intermittent Wiper ("INT" position on stick) BR70-66-120G Read More
It could be on either side, but the turn signal lever is almost always on the same side of the steering column as the steering column is on the side of the car. Earlier cars have it as a twist grip on the end of the turn signal lever. Newer ones often have the control as a separate lever on the opposite side of the steering column. Read More
check the third light and brake lights, check the fuses, if all are ok then change the multi- fuction switch aka turn signal switch. Read More
Low beam bulb burnt out? Replace bulb. Bulbs OK? If the dimmer switch is also the turn signal/cruise/headlight on and off switch, you probably have to replace the entire switch. Read More
The problem is your multi function turn signal switch. It usually controls your High beams, turn signals, and washers, or cruise control. When they go bad all kinds of weird things can happen. Read More
When the windshield wiper on a 2000 Ford Ranger comes on by itself this can signal a damaged windshield wiper switch. Changing these switches out often corrects this problem. Read More
How do you replace a turn signal bulb in a 1998 cavalier Read More
Control unit generates all the control signals like memory read signal,i/o read signal,memory write signal etc Read More
On a 2000 Ford Expedition : The rear windshield wiper control is on the inner part of your turn signal lever towards the steering wheel column cover . It has OFF / INT 1 / INT 2 positions Read More
on the turn signal switch Read More