0
use a keeper ring, it looks like a washer only with teeth on the inside the id of the ring will be the od of the pin. slip ring on and insert pin if done correctly the pin stays put. use a ring on top and bottom
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
What is the name for pin that slides into a door hinge?
door hinge pin
How do you replace a door hinge pin in a 1997 grand marquis?
To replace the door hinge pins on a 1997 Jimmy you will need to open the door up. Place two jack stands on the front and back of the door's length at the bottom portion of the door for support. Remove the damaged hinge pin with the proper socket. Place the new hinge pin in place and secure it.
How to remove 1991 camaro door hinge pin?
Open the door, support it with a jack, remove the hinge spring. To remove the pin, you should have to remove a retaining clip at the head of the pin and then tap it out with a hammer. The upper hinge has two bolt secured bushings. Unthread the bolts, tap them out with a hammer and pull out the bushings. Make sure the door is held secure, as it will be free floating at this point.
How do you remove the front door hinge pins on a 1995 Jeep Grand Cherokee?
Door pin/bushing replacement guide: http://www.digitalrevo.com/jeep/doorpins.html
What is a door hinge pin?
A hinge pin is a pin that holds together two hinge plates, one of which is fastened to the door and the other is fastened to the door jamb. There are usually two or three hinge assemblies used on each door, one near the top, one near the bottom, and sometimes one at the middle.
How do you replace door hinge pins on a 1993 Mercury Cougar?
Hold the end of the door with a jack, grind the head from the old pin, knock out the old pin, remove the door half of the hinge, drill out the hinge to accept the new bushings, install the new bushings, re-bolt the hinge to the door, finally, insert the new pin and install the C clip
How do you replace door hinge pin and bushing on Crown Victoria?
The pin will probably have to have the bottom end that is flared out cut off or drilled out. The pin can then be tapped out. This is easier if the hinge has been removed but then the door will have to be blocked up into place while the hinge is off.
How do you change door hindge pins on 1994 thunderbird?
you buy a hinge pin replacement kit made for the f-150 truck and use it on your bad hinge... worked like a champ on my 95 cougar
How do you replace a hinge pin bushing on a 1997 Jeep Grand Cherokee front door?
You can purchase replacement hinge pin and bushing kits from Napa, O'Reilly, Etc. Part numbers are: Dorman 38422 NAPA 675-1594 They are about $5.99 per pin, (2) required per door. Then you have to install as listed below on digitalrevo. There is a hinge kit available from dealers- my understanding is that it's pretty expensive, and replaces the complete hinge, so it requires welding a new hinge to the door. My door was rusted out at the bottom anyway, so I bought a complete replacement from a salvage shop. Here's a guide to replace the door pins and bushings. http://www.digitalrevo.com/jeep/doorpins.html Digitalrevo is not an active website as of 12/24/07
How do you replace a 96 thunderbird driver side door bottom hinge pin?
You have to replace the whole hinge assembly, they don't make a hinge pin kit for the Thunderbird.
Is the front door top hinge welded or bolted on to body 95 Jeep Cherokee?
It's bolted on the body, welded on the door. Door pin/bushing replacement guide: http://www.digitalrevo.com/jeep/doorpins.html
How do you change door pins and bushings on a 1999 Chevy blazer?
REMOVAL & INSTALLATIONSee Figures 1 and 2 Fig. 1: A spring compressor tool must be used to remove the springs when working on the doors/hingesFig. 2: Exploded view of the door hinge pinsThe following procedure requires the use of a door hinge spring compressor such as J-36604-A or equivalent. # If equipped with power door components, perform the following procedures: ## Disconnect the negative battery cable. ## Check for access to the wiring by removing the cowl side vent cover. If access is possible, remove the receptacles from the wiring harness, then remove the retainer from the wiring harness grommet. Remove the rubber conduit from the door pillar by pushing it from the vent cover side. ## If access is not possible, remove the door trim panel, then unplug the electrical harness connector from the power door lock motor and/or the power window regulator. Remove the harness from the door. # If available, apply cloth-backed tape to the door and body pillar for protection. CAUTIONBefore removing the hinge spring from the door, cover the spring with a towel to prevent the spring from flying and possibly causing personal injury.# Using a door hinge spring compressor such as No. J-36604-A or equivalent, compress the door hinge spring and remove it. # To remove the door hinge pin clips, spread the clips and move them above the recess on the pin; when the pin is removed, the clip will ride on the pin and fall free of it. ## Using a soft-head hammer and a pair of locking pliers, remove the lower pin from the door hinge; then, temporarily install a bolt (in the lower pin hole) to hold the door in place until the upper hinge pin is removed. ## Remove the upper door hinge pin and support the door, then remove the bolt from the lower hinge pin hole and remove the door from the vehicle. To install:# To install the door, position it on the hinges and insert a bolt through the lower hinge pin hole. # Using a new hinge pin clip, install the upper hinge pin. # Remove the bolt from the lower hinge pin hole. Using a new hinge pin, install it into the lower hinge pin holes. # Compress the door hinge spring and install it into the door hinge using the door hinge spring compressor tool. # If equipped with power door components, re-engage the wiring and install the trim panel or pieces, then connect the negative battery cable. ADJUSTMENTSFactory installed hinges are welded in place, so no adjustment of the system is necessary or recommended. Service replacement hinges are bolted in position and may be adjusted. If your vehicle is equipped with service replacement hinges, please refer to the door hinge adjustment procedure located later in this section. Depending on the type of door hinge you have, you wont have the clips mentioned above. If this is the case there will be a silver cap that sit on the top of the door pin. all you have to do it hit the top of the pin with a BF hammer (or rubber hammer) and a punch. The pin will come straight out. One thing to be aware of, as soon as that pin is out it will put all the pressure on the other pin. U should use a bucket and place it under the door so that it doesnt fall too much. I did mine yesterday and it took about 30 minutes. If you have the right tool (which I didnt) and someone to help you it should be no longer than 30 minutes. Good Luck!!!!!!
