Chevy Corvette
Ford Expedition
Ford Expedition Eddie Bauer
Ford Expedition XLT
How To

How to remove passenger side door panel on 1991 corvette convertible?

333435

Top Answer
User Avatar
Wiki User
2014-10-07 02:13:44
2014-10-07 02:13:44

The 1991 Chevrolet Corvette convertible passenger side door panel is held in place with two retaining bolts and eight retaining clips. Remove the retaining bolts and pry outward on each retaining clip.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

remove the screws on the inside fender well, take out the bolt in the top of the louvered panel, pull panel out slide battery out.

User Avatar

Inside the passenger-side door on the right side of the dash there is a panel (6"x6"? Rounded corners. Remove panel.

User Avatar

Didn't make a convertible in 1984. It has Targa roof panel that can be removed with a tool.

User Avatar

The reason for the problems with the horn on the Corvette could be attributed to a faulty fuse or horn relay. This can be located in the fuse and relay box that is located under a panel on the passenger side floor board.

User Avatar

( # 20 ) is a 15 amp fuse for the convertible top switch ( located in the passenger compartment fuse panel , below and to the left of the steering wheel by the brake pedal . Remove the panel cover to access the fuses .

User Avatar

Under the passenger side instrument panel. Remove panel by removing screws in side fuse box. Drop panel. You will see several relays. It is the middle of three relays nearest the radio.

User Avatar

under passenger side of dash remove panel were interior light is and you will see fuse holder with four fuses

User Avatar

Remove the inside door panel of your 1982 Chevy Corvette. Remove the window retaining clips. The window will lift out.

User Avatar

passenger side of dashboard facing the door.

User Avatar

The fuse panel is on the right end of the dash, open the passenger side door and look at the dash where the door comes up agaist it. You will see a small door turn the knob and remove the panel to expose the fuses.

User Avatar

The fuse panel is located on the right side of the instrument panel. Open the passenger door and you will see it.

User Avatar

On the side of the dash exposed by opening the passenger side door.

User Avatar

You need to remove the small vented side panel. or at least remove the 3 screws from the wheel well and the one on the top of the panel. Then pull the panel out enought to remove the battery

User Avatar

the fuse box on a 1985 corvette is located on the side panel of the dash on the passenger side . Open the passanger (right side door) and box is on side of dash.

User Avatar

Using a screwdriver, remove the screws from the panel, remove the clips from the panel, and pull the panel away gently. Remove any wiring connectors, and remove the panel from the frame.

User Avatar

Use the right sized screwdriver, remove the screws and panels from the door panel and pull the panel away. Remove the wiring connections, and the panel should come free.

User Avatar

Using a screw driver, remove the screws and clips from the panel. Pull the panel away from the frame, remove the wiring connections, and the panel will come free.

User Avatar

Using a screwdriver, remove the screws and clips from the panel. Pull the panel away slowly, remove wiring connections and the panel will come free.รŠ

User Avatar

You need to remove the Rh lower insulator panel, this is the panel with the courtesy lamp. remove the push pin retainers to the panel, then un clip the courtesy lamp from the panel, then remove panel. Remove blower motor connector, remove 3- 5.5mm screws, then lower and remove the blower motor..

User Avatar

you have a main fuse panel on the right side of the dash,passenger side.Open the passenger side door and you can see it,there are also fuses located under the hood behind the battery

User Avatar

How do you remove back door panel off 2005 grand marquis

User Avatar

remove door panel then remove screws behind mirror. remove door panel then remove screws behind mirror.

User Avatar

i usually use a sawsawll. or a table saw.

User Avatar

The 2000 Chevrolet Blazer passenger side kick panel is held in place by eight retaining bolts. Remove the retaining bolts and the kick panel will come free.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.