0
What can i do i am trying to get the fan off the water pump and removed the bolts on the pulley what else?
Wiki User
∙ 15y ago
in this order from start to stop you remove the fan shroud from the radiator then you loosen the belt that is around the pulley behind the fan then you remove the bolts that are between the fan and that pulley then remove the fan you might have to lightely tap it with something to break it lose from any dirt and crud but should come rite out!
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace a serpentine belt and water pump pulley on a 1990 Cadillac DeVille?
I just recently changed the water pump on my dad's 1990 Cadillac Deville. It was an undertaking let me tell you. First you have to take a 1/2" ratchet and position it in the place on the belt tensioning pully and pull it toward the front of the car. This will allow you to completely remove the belt. Take note as to how it is oriented around the various pulleys and the back idler pulley. I found that even after I had removed the three bolts that hold the water pump pulley to the water pump itself, I couldn't just remove the pulley. There wasn't enough room between the pulley and the frame. I was removing the water pump anyway, so I painstakingly removed all of the water pump mounting bolts and nuts, and removed the pump with the pulley loose. There are several bolts you can't get to anyway, unless you take the pulley bolts out. I just had to move the pulley to one side or the other in order to get to the bolts under the pulley. Installing the new pump had to be done in the reverse order. The lip of the pulley catches on the water pump shaft and that keeps you from being able to remove it. There may be an easier way, but I couldn't find one. I didn't want to take a lot of parts off to just to get the pulley out of my way. It's tough, but it can be done. I have the cut up hands to prove it. I hope this info helps you.
How do you get the water pump bolt that is behind the pulley for the power steering pump loose when all other bolts are out and you pulled a muscle trying to get the pulley off?
You need to remove the entire power steering pump. There are two bolts holding it on at the 12 and 6 o'clock position. Remove these via the holes in the power steering pump pulley. (no need to remove the pulley) Push the pump to the side and you then have access to the water pump bolt. Hope this helps. "G"
How do you put on a water pump pulley for the serpentine belt on a 1995 Chevy Lumina minivan?
there should be 3 or 4 bolts that hold pulley on, just remove these bolts a pulley should come off. but remove belt first ! if pulley keeps turning while removing bolts. you can hold it stationary with a scredriver or similar.
How do you remove the fan clutch to replace the water pump on a 1996 dodge Dakota?
First, the neg. battery cable should be removed from the battery, the appropriate belts should be removed, the rad should be drained to at least as low as the bottom of the water pump's lowest point, and the top rad hose should be removed. Then the fan shroud bolts should be removed. The fan and clutch should be attached to the water pump hub by a large threaded nut. If the fan clutch itself needs to be dissassembled, or if the water pump pulley bolts can't be accessed with the fan present, then wedge a prybar or long screwdriver between the pulley bolts to prevent the fan turning and, using the appropriate size wrench, turn the large nut counterclockwise to loosen and remove it. If the water pump pulley bolts can be accessed then remove them and pull out the fan assembly and the fan shroud together. Installation is the reverse of removal. Don't forget to put the shroud and fan back in together.
Where is the water pump located on a 1989 Chevrolet Corsica V6?
The water pump is located behind the water pump pulley. The water pump pulley is the smooth pulley at the top closest to the front of the car. It is held in place by 4 bolts with 8mm heads. The pump is held in place with 5 bolts. Warm the engine to operating temperature before removing the bolts or they may break off causing you greif.
How do you replace the water pump in a 2002 3.8L Impala The water pump is stuck with all the bolts out how do i get the water pump off?
The steering pump is attached with 2 bolts. If you take the top bolt out and loosen the bottom bolt until it's almost completely out, you can move the pump/pulley enough to snake that bottom left water pump bolt out.
How do you replace a water pump on a 1991 Suzuki Swift?
# Remove air filter to give you more room to play # Loosen alternator and alternator tensioner. Alternator tensioner bolts to water pump so that bolt will need to come out. # With the alternator loose, the main drive belt should be loose and be able to be removed, do this. # Loosen the tensioner bolt for the air conditioner, on the underside of the engine. Losen the nut on the air conditioner tension wheel. The tensioner wheel should now slide up and down freely, allowing removal of the air conditioner belt. # Remove the 4 x 10mm bolts on the water pump pulley. Remove the water pump pulley. # Remove the 4 x 10mm bolts on the camshaft pulley. This is the main pulley that all the belts connect to. There is a large 17mm bolt in the middle of this pulley that does not need to be removed. (Crankshaft Bolt). # The camshaft pulley should slide off, however you will probably have no clearance (because of the crankshaft bolt) to remove the pulley. The pulley has to be removed. # Place a jack under the sump, use a piece of wood to protect the sump. Jack the sump up 1/2 inch. Undo the two 14mm bolts in the engine mounts. When the two left hand engine mount bolts are out, lower the jack slowly until you can slide the camshaft pulley out. # Remove the plastic timing belt cover. # You should now see the timing belt, remove the timing belt tensioner pulley, being careful not to move the timing belt wheels. # Undo the bolts holding the water pump. # Water pump should come off, water will come out if you haven't drained it. # Scrape off gasket. # Install new water pump. # Reassemble in reverse order.
How do you change the water pump with pulley on a 1986 Chevy Celebrity Eurosport 2.5L?
These are typically easy to changed first take off the pulley then you will have access to the bolts they behind the pulley
How do you replace the water pump on a 1994 Nissan Sentra?
Not sure on a '94, but on a '90 w/ a 1.6 you just remove the pulley bolts on the water pump, take off the pulley and belt, remove the thermostat housing on the side of the water pump, and then remove the water pump bolts. After that you can take off the water pump.
How do you get to the bolt located behind the power steering pulley to take out the water pump when there is no holes in the power steering pulley to remove the power steering pump?
Are you sure that bolt has to come out to change water pump? That bolt should be one of three that hold the p/s pump to the bracket. Those bolts are removed by removing the p/s pulley first. That requires a special puller to r & r the p/s pulley.
How do you install a water pump on 1964 Oldsmobile 98?
First remove all hoses, then remove the radiator, then remove the bolts of the water pump pulley (the big one in the middle of the engine), then remove all belts, you will see some bolts which fasten the pump to the block (around where thepulley was) take them all out and the water pum will be loose and easy to be removed.
How due you remove the water pump pulley from a 1997 Chevy venture the pulley turns every time you try to undo the bolts?
put the belt back on and hold the pully with your hand while losing the bolts with a wrinch
