0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
Why did Chevrolet go back to drum brakes on the Silverado from already have 4 wheel disc?
Drum brakes are cheaper to build.
What cars were made during World War 2?
Cars were made for all the military sevices, army, navy, coast guard, and others. Some cars were sold to Doctors, nurces, and other persons considered necessary to protect the public. Lots of cars were put in storage, and production was very small as most auto plants were converted to producing war materials. But cars were produced and sold in very limited numbers. Some particular models were not produced at all. I know the Chrysler Corporation built some cars during WW2 that were sold to civilians on a must need basis, but not sure about any other manufacture.
Where is the Chevrolet epica 2007 obd-II connector?
under stearing wheel. There is no need to unscrew or open anything.
Where is the fuse block on your 1956 Chevy?
Drivers side, below the dash, against the backside of the firewall.
What size motor is a 2000 Chevy ls 1500?
Check the sticker on the fan shroud... It should say on there, near the top-left corner. If it says 5.0L it's a 305 cubic inch motor, if it says 5.7L it's a 350 cubic inch motor...
How do you remove the ECM from a 1989 Chevy K1500 Scottsdale 4X4 Pickup?
FIRST, disconnect your battery. Then remove the glove box (4 small bolts/screws, two on each side). The ECM will be behind the glove box on the right side (it's the shiny metal box approximately 6"Long x 4"Wide x 1.5" Thick). Slide/pull it carefully to the left (towards you). You may have to pull open the two clips on the left side of it a little to get it loose (very easy to do by hand with you fingers). When you have moved it to the left and have enough room, disconnect the two wire connectors right in front of it. Move the connectors out of the way and pull the ECM out. Very simple job. To remove the chips from inside the ECM all you have to do is remove the two small screws that are holding a small plate on top of it. They are directly under that plate. I used a flathead screwdriver to CAREFULLYpry on each side of the chips evenly to pull them out. Again, very simple.
Where does vacuum line connect from 400 turbo to 400 small block chevy?
Well, the tranny modulater, requires manifold vaccuum, to make the trans shift. So, a runner on the intake, or the carb BASE PLATE. Now, if you have a vaccuum line, you probably have a TH350. If the oil pan on it is shaped like an square, with a notch cut out of one of the corners, it is a TH350. 400's, do not require vaccuum.
Where can i find original wiring diagram for 1965 Chevy truck for both steering column and fuse box?
The LMC truck product catalogue has the 1963 repair manual with supplement for 1965 which includes the wiring diagrams.
Where is the low pressure valve on the AC for 2002 Trailblazer?
On all GM products it is almost always on the accumulator / receiver drier.
Driver side front and back carpet for 2009 HHR soaked?
Usually that is a sign that the heater core or windshield are leaking.
High performance parts for 1994 LT1 Chevrolet engine?
Search Jegs.com, theres lots. Headers, ignition, throttle bodies, superchargers etc.
Why is your brake light flashing 6 times on your 89 Chevy when the key is on?
You may be low on brake fluid, you may have worn-out brake pads. It may be something easy like a bad electrical connection. Best to get it checked by a proffessional; after all we are talking about brakes here.
What pushes the valves in an engine open?
The cams on the camshaft.
NEW ANSWER : Yes it is the camshaft, But it is the LOBES on it that makes the valves open and shut. Not the Cams that's on it, No such thing.
Response to new answer: look up cam in a dictionary or on wikipedia. It's an irregular fitting on a camshaft that converts rotational motion to reciprocating motion. That said, the term "cam" is interchangeable with "lobe".
What was the most popular in 1951?
Most popular Chevrolet? The most popular model sold was the Styleline 4 door.
Will Pontiac 400 manifold fit Chevy 400 engine?
No, I do not think so as they are not the same engine.
What car did this engine come out of 68 serial V0227HM?
V = Flint MI
0227 = February 27
HM = 327 CI from a Full Size...probably a truck
How do you remove a broken valve cover bolt on a small block Chevrolet?
the easiest way is to drill it out. drill a hole thru center of broken bolt, make sure it is smaller then the diameter of the bolt. after drilling use a easy out to remove the threads of the bolt. check that the threads in the head are ok! then put in new bolt.
Where are Chevy Silverados made?
It depends on what part of the country you live in as to where the silverados are made. For consumer silverados most powertrains, suspensions and frames are built in illinois and Michigan. Assembly plants range from Canada, Michigan, Wisconsin, and Texas. Most industrial work trucks are built in the same factories with most of the global export vehicles being built in Mexico.
What is stock symbol for Chevrolet?
It has no stock symbol. It is a part of General Motors, so would be included in GM.
