Computer Networking

It would say so in the bottom corner.

A layer 2 switch may need an IP address if the operator wishes to be able to access it without a serial cable. With an IP address, the switch can be access from anywhere with a connection to the network or an Internet connection.

A DS1 is a telecommunications standard used in North America, Japan, South Korea and some Pacific islands and territories. The term stands for 'Digital Signal [level] 1.' A T1 is the actual 4-wire circuit used to transport the DS1 signal, and the two terms are often used interchangeably. A DS1 signal is part of the [North American] Time-Division Multiplexing heirarchy, and operates at a speed of 1.544 Mbps (Megabits per second), including 8 kbps (kilobits per second) of framing bits. The signal is comprised of 24 timeslots of 64 kbps DS0 (DS-'zero') channels. The DS0 is the most basic unit of the TDM heirarchy, and can be considered the equivalent of a regular voice phone line (56 kbps + 8 kbps of signalling) or a digital line (of 64 kbps), so a DS1 can be said to contain the equivalent of 24 phone lines on one 4-wire circuit. The T1 circuit uses a separate transmit pair (2 wires) and a receive pair (2 wires) and operates at the effective speed of 1.544 Mbps in both directions simultaneously.

There are many different protocols depending on transmission speed used, the type (phone MODEM, cable MODEM. etc.) and other conditions.

There are far too many to list here.

Usually a gateway or proxy is responsible for hiding internal networks.

Proccessing, mostly every program is run using it.

The error continues to be present in the system until it is flushed out, since at each iteration all bits move 8 places to the right (or left).

router

router

Control panel -> User accounts.

Depending on your Windows version you might have to click "Manage another account" before given the possibility to "Create new account". Choose "Administrator" in the setup wizard.

providing portable connectivity,and also provide data and telecommunication services

Get a program to scan and create the network map. After you have created the map, use annotations to mark where they are in the building.

ISDN: Integrated Services Digital Network

DSL: Digital Subscriber Line

SSH and HTTPS

The routing table acts like a map for a router. It stores the different routes that a signal has taken to get from one point to another. It stores the information about pings, fixes, stalls and errors that fall into the static route file. The routing table can be extremely helpful in determining the shortest route for a signal as well as being able to have it auto-fix errors when encountered in the future.

You have to register with Magix. Once you have an account, go to the activation section and click on it. It will provide you with one. Copy it then paste it into the Activation Code area on the message you receive in the program.

Peer to Peer means all connected computers may act as either servers or clients. (A peer is an equal.)

LAN: Limited geographical area usually within the same building.

WAN: Larger global Network with no physical boundaries.

Port 8080 is an alternative to the port 80 used by http and web services.

History:

The Internet was largely born on UNIX-based systems and servers. UNIX enforces the notion of the first 1023 "privileged ports" which can only be opened by services running with so-called "root", or administrative, privileges. Historically, this meant that only authorized system administrators were able to establish and operate a web server on port 80 since this was within the first 1023-port privileged region. Therefore, when non-administrators wished to run their own web servers on machines which might already have a server running on port 80, or when they were not authorized to run services below port 1024, port 8080 was often chosen as a convenient place to host a secondary or alternate web server.

ssh

if its 2D its a octagon, if its 3D its a octagonal prisim

Between the wireless network and the wired network

It depends on how many subnets you have and how many ports you router has. Usually each port in router is devoted to on subnet, you can do math for your situation.

In cases where a connection is established, the sender, the receiver and the subnet conduct a negotiation about parameters to be used. Parameters like maximum size of the message, quality of service etc are considered. One side can make a proposal and the other can accept it, reject it or make a counter proposal.