Construction Tools

Makita is the manufacture of the power tools sold at Menards using the Masterforce brand. It is Makita,s way of getting more company sales to help the companies bottom line in revenue (sales). This from a regional sales manager from Makita. R.F. Midwest region

I also keep mine in a toolbox in the garage

Mag Aral kayo Mabuti. Wag Puro Research. :P

Use a standard HSS drill bit, but slow down rotation to about 500 rpm.

A range of wrenches going from 3/16 up to 3/4 inch , composing 10-12 wrenches is usually considered a complete set. Many mechanics have these sets in SAE and metric and in flat, box and ratchet.

Stanley Corporation now makes Black and Decker power tools in India and China.

yes, i am not trying to sound like a smart alek but if you don't know the answer please seek advice from a professional roofer you will be better off in the long run.

==================

Check with the info on your shingles, some recommend NOT putting down tar paper first others go as far as voiding the warranty if you do install them over tar paper.

Personally, I would not put shingles on my own house without tarpaper, it is a cheap and fast extra layer of protection from water that can cause a lot of damage sometimes before you can see it.

You can find a Sliding Mitre Saw at Home Depot. They have a Dewalt 15 Amp. 12 inch Double Bevel Sliding Compound Miter Saw available for just $599. each. You can find it at Home Depot online or in their stores.

Generally, blades have more teeth closer together the harder the material gets. Soft wood blades have as few as 3 teeth per inch. Hardwood and laminate blades have 10 or more smaller teeth per inch. Hacksaw blades for hard metals may have 32 teeth per inch.

A Tenon Saw is the most used kind of backsaw (a saw with a piece of stiff brass or steel running along the top edge). It is a medium sized saw and originally obtained its name from its use in cutting tenons for mortise and tenon joints in woodwork. The stiff piece of metal along the top of the blade (like all backsaws) helps prevent the blade from bending during use and the added weight adds another level of control to the saw.

There are many different hammers and all are suited to a particular job. I have at least 8 totally different hammers and there are lots more. They are suited by different shaped heads, different materials and different length and style of handles. Look in big tool store and you will see at least 10 radically different ones.

rip

cross cut

cut curves

cut circles

Positive

Negative

Neutral

Time Out

1999 - That is the date my father put on his manual when he bought it.

A 10 cm hole is almost 4 inches ! ! - IF you meant 10mm, then that's a little over 3/8 of an inch, or 13/32 for a clearance hole.

I believe on that model the chuck would be a Morse taper fit. To remove it, extend the chuck spindle to it's lowest position and use a metal hammer to tap firmly ONCE on the top of the chuck. It should drop free. Make sure your new chuck is the same and clean the inside of the taper and the arbor taper with alcohol (NOT rubbing alcohol, -99 % alcohol) Then fit the dry chuck onto the arbor for a test fitting. If it slides on easily, raise the arbor to the top and line up the chuck with spindle, retract the jaws and tap once with a steel hammer upwards on the base of the chuck. It should seat on firmly and you are ready to drill.

13

For coarse threads (13 threads per inch) use a 27/64 drill

its quite confusing best buying one unless you have the blueprints

Today, twist drills are made on computerized grinders

Go back pre computers - picture a horizontal mill/grinder with a wheel the thickness of the flute spinning

The table of the mill is set so the the wheel sits at the angle of the flute, and the drill blank is in a rotary fixture on the table, so that when the table is moved (in what is called the X axis) the drill blank rotates at the appropriate rate

You lower the wheel a .001 or so, traverse the table, and repeat - either between passes, or at the end, index the blank 180 degs to do both flutes, OR in a production setting (aka you're a drill bit company), your grinder will actually have two wheels, with the wheels offset to the table, but the bit still rotates as the table traverses, so you gring BOTH sides of the bit at once

There is no definite date on that, but tenon saws have been used for at least 200 years just the way we see them now.

Depends on the chuck. Adjustable chucks can be loosened by hand, simply twist the end of the drill. Older (or heavy duty drills) need a key to open the drill chuck. I have a McKeller cordless 18V electric drill with no hand adjustable or key adjustment visable???? I'm confused

The lever class of a hammer depends upon its use. If the hammer is used as a claw to remove a nail, it is a first class lever. When the hammer is used to strike a nail, it is a third class lever. There are three classes of levers. The difference between the classes lies in the position of the load, the effort and the fulcrum. When the fulcrum is between the load and effort, the object is a first class lever. If the load is between the fulcrum and effort, the object is a second class lever. A third class lever places the effort between the load and the fulcrum.

Wood chisels come in many different sizes or shapes. Each size/shape serves a very particular function. Some of these incluce; Butt, Carving, Corner, Bevel edge, Flooring, Framing, Slick, and Mortis.