Flooring

To remove water stains from wax floors, mix equal parts of white vinegar and water in a spray bottle. Spray the solution onto the affected areas and let it sit for a few minutes. Wipe the area clean with a damp cloth, then dry thoroughly with a separate cloth. This should help remove the water stains from the wax floor.

Settlers had a rough time crossing the rugged Appalachian Mountains.

To remove sticky residue from wood floors, you can try using a mixture of equal parts vinegar and water. Apply the solution to the sticky area and let it sit for a few minutes before wiping it away with a clean cloth. You can also try using a commercial sticky residue remover specifically designed for use on wood floors.

To remove lemon juice stains from marble flooring, mix baking soda with water to create a paste. Apply the paste to the stained area and allow it to sit for about 24 hours. Then, wipe it off with a damp cloth and rinse the area with water. Repeat the process if necessary.

Tough question, easy answer, trial & error.

Start with scraping, use something like the edge of a credit card

then try a damp soft cloth and start easy & work your way toward more agressive. If it's not budging, move on.

Always put the solvent on the cloth & try it in an area away from sight if possible.

any or all of these could ruin your floor, but unknown white substances may have already done that, so we are looking for reversal or improvement..

Might try something like windex; pretty mild but a bit of alcohol & a bit of detergent.

WARNING from here on it is likely that these may ruin the finish.

Then move on to cooking oil or PAM spray

then move up to WD-40

then on to mineral spirits on a cloth

beyond that there is always sanding & refinishing.

Ingredients in AJAX floor cleaner- Calcium Carbonate (purpose is a cleaning agent), Sodium Dodecyl Benzene Sulfonate (cleaning agent), Trichlorocyanuric Acid (stain removal), Fragrance (pleasant scent), Dye (for its color).

When sitting on the floor, typically the ischial tuberosities (the bony prominences at the bottom of your pelvis) are in contact with the floor. These are the "sitting bones" that help support your body in a seated position.

There is no product other than "Dry moving air" that will absorb mass quantities of water from a carpet.

There is a product called Capture, from Milliken co. that is absorbent but it is designed as a cleaner not an absorbent fro removing water.

The other thing to be careful with is the subfloor, and carpet padding if any. That will not dry with the carpet still over it & mold & mildew become a real issue very fast. If a wood subfloor stays wet very long expect buckling and degradation of the wood subfloor. You need to get it all dry & fast.

The part of the stair you don't step on is called the riser. It is the vertical section that connects each step.

Tiles with a rough surface provide more traction and grip, reducing the risk of slipping or falling, especially in wet areas. The texture on rough tiles helps to increase friction, making them safer to walk on compared to smooth tiles which can be slippery, particularly when wet. The rough surface of tiles also disperses water and allows for more secure footing, making them a better choice for areas where slip-resistance is important.

You can try cleaning the yellowing floor tiles with a mixture of baking soda and water or a commercial tile cleaner specifically designed for whitening. For persistent stains, you may need to consider professional cleaning or resealing the tiles. Regular maintenance and cleaning can also help prevent future yellowing.

A vinegar and water solution, or a mild dish soap diluted in water, can be effective floor cleaners that do not leave a film behind. Additionally, using a microfiber mop to clean and dry the surface thoroughly can help prevent a film from forming.

Grout is cement, sand & a liquid, the liquid starts the process of the cement & sant setting from a powder to a solid.

Traditionally it was WATER that was used as the liquid

newer grouts substitute Epoxy as the liquid, making the grout set harder stick together better and resist stains

A credit card works pretty well and once most of it is off rub with a clean dry cloth. If there is still a residue, you might try pam cooking spray or WD 40. They usually work & wont hurt most floor finishes. Spray it on the cloth not the floor & try in a closet or corner first.

Laminate floors may creak due to improper installation, poor subfloor preparation, or the floorboards rubbing against each other. Humidity changes or an uneven subfloor can also cause creaking. Fixing the issue may involve ensuring the subfloor is flat, using the correct underlayment, or adding lubricant between the floorboards.

To remove salt residue from a tile floor, mix equal parts water and vinegar, then mop the floor with this solution. Alternatively, you can use a commercial tile cleaner specifically designed to remove salt residue. Make sure to rinse the floor thoroughly after cleaning to prevent any damage or stickiness from the vinegar.

My nephew had applied polyurethane to the bedroom floor and accidentally got some on the linoleum flooring outside of my bedroom. I tried taking it out with goof off and paint thinner to no avail. I decided to see if I could lift the stain by applying steam to it. So I kept applying steam with my Shark Steam cleaner for a couple of minutes. It seem to loosen the stain. I then used a small scraper, wrapped it in a Lysol wipe and was able to remove the stain with a little elbow grease. Thank goodness it was a small area here and there. Hope it works for you.

Ann Marie, The Bronx

New grout will not bond well to old grout because the surface of the old grout may be too smooth or uneven to create a strong bond. It's recommended to remove the old grout before applying new grout for a better adhesion and more consistent finish.

No, it is not recommended to laminate over a magnet as this can interfere with the magnet's ability to attract or adhere to metal surfaces. The lamination process may also damage the magnet or cause it to lose its magnetic properties.

Say it was high gloss, if the wood soaks it in deep and you only put two thin coats on

it will not shine like it should.

Because it should shine a lot. Can depend on how much gets absorbed by the wood.

All grout dries lighter when dry.but brown grout should

not dry white. Check the date of; it might be passed its

shelf life.

look and see if you bought a light brown grout.

You could cut the grout out with a grout rake but this would take ages

The person on the top floor will receive less water because they are against the force of gravity, which creates less pressure in the pipes. As water is pulled downwards, the pressure decreases with height. This results in a lower flow rate for the person on the top floor compared to the person on the ground floor.

To remove champagne from carpet, blot the area with a clean cloth to absorb as much liquid as possible. Then, mix a solution of water and a gentle detergent, and blot the stain with this mixture until it fades. Finally, rinse the area with clean water and dry it thoroughly.

It is not recommended to put vinegar in a steam mop as it may damage the internal components and void the warranty. Using only distilled water in the steam mop is the best practice to ensure its longevity and proper functioning.

Muractic acid available in most commercial retail outlets typically runs 30+ or - % Hydrochloric Acid content. Nasty stuff and generally speaking it will at the very least etch the surface and take the satin or glazed finish "OFF" a tile.

My company just finished litigation with one of our clients that used a proprietary method of ours to test a surface for waterproofing of a surface after applying our waterproofing product. We call for a water and acid test on surfaces to qualify for our 15 year warranty for waterproofing. This guy instructed his in house maintenance personnel to perform these test after looking at our web site, "without our knowledge or permission" and not only ruined thousands of sq. ft. of tile, but also had OSHA involved. Big Mess!

Don't know what your trying to do, but Muriatic is Bad Stuff in the wrong hands and we don't even recommend it's use for " Acid Etching of Concrete", that used to be a standard for coating applications, "Back in The Day" That's why it has the skull & crossbones on it!