Ford Focus

Error code C1093 for a 2005 Ford Focus typically indicates an issue with the ABS (Anti-lock Braking System) module, specifically related to the wheel speed sensor circuit or a malfunction within the ABS system itself. This code can signal problems such as a faulty wheel speed sensor, damaged wiring, or issues with the ABS control module. It's advisable to perform a thorough inspection of the ABS components and wiring to diagnose and address the problem accurately. If needed, a professional scan tool can help pinpoint the exact issue.

The Isuzu 4JA1 engine is a 2.5-liter diesel engine that features a Single Overhead Camshaft (SOHC) configuration. This design typically includes eight valves, with two valves per cylinder. The SOHC setup is common in many diesel engines for its simplicity and reliability.

To open the hood on a Ford C-Max, first locate the hood release lever inside the vehicle, typically found on the driver's side near the door. Pull the lever; you should hear a pop indicating the hood has been released. Then, go to the front of the car, slide your hand under the center of the hood, and find the secondary latch. Push the latch to one side while lifting the hood to fully open it.

To preset radio stations on a 2015 Ford Focus, first tune to the desired station using the radio controls. Once you have the station playing, press and hold one of the numbered preset buttons (1-6) until you hear a confirmation beep or see the station name appear on the display. Repeat this process for any additional stations you want to preset. You can access your saved stations by simply pressing the corresponding preset button.

The weight of a Ford Focus typically ranges from about 1.3 to 1.6 tonnes, depending on the model year and specific trim. Most standard models weigh around 1.4 tonnes. It's important to check the specifications for the exact model you're interested in, as weights can vary with options and configurations.

To replace the gear knob on a Ford Focus ST170, first, ensure the car is in neutral. Grip the base of the gear knob and pull it straight up to remove it, as it is usually held in place by clips. If necessary, you may need to twist slightly or use a cloth to avoid damaging the knob or surrounding trim. Once removed, position the new gear knob over the shift lever and press down firmly until it clicks into place.

Oh, dude, the 2012 Ford Focus has like... wait for it... 16 valves! Yeah, that's right, 16 valves working hard to make that car go vroom vroom. So, if you were ever wondering how many valves were in a 2012 Ford Focus, now you know!

Product information

Technical Details

Brand ‎Purolator

Material ‎Synthetic, Metal

Product Grade ‎Performance Part

Vehicle Service Type ‎Truck

Item dimensions L x W x H ‎3.31 x 3.19 x 3.31 inches

Item Weight ‎0.6 Pounds

OEM Part Number ‎PL14459 "ENGINE OIL FILTER"

Global Trade Identification Number ‎00076333116381

Manufacturer ‎Purolator

Vehicle Fitment Note ‎Compatible with truck models

Number of Items ‎1

UPC ‎076333116381

Model ‎PL14459

Item Weight ‎9.6 ounces

Product Dimensions ‎3.31 x 3.19 x 3.31 inches

Country of Origin ‎China

Item model number ‎PL14459

Exterior ‎Painted

Manufacturer Part Number ‎PL14459

Its not too complicated.

1. Look on under side of bumper, you will see four 7mm bolts holding two light assemblies in place.

2. Loosen these four bolts but don't remove them. A 1/4 or 1/2 inch ratchet with a 7mm socket will expedite the process.

3. Slide the assemblies toward body of the car (about 1 inch) so they are loose. The bolts ride in a slot.

4. Slide a loose light assembly toward the other light and gently pull out so the assembly is hanging free of the bumper with about 4 inches of wire. You'll see the opening in the bumper housing is wider in the space between the lights. I needed to gently push up on bumper housing plastic to get the assembly out, but then it came out quite readily. Repeat this step so both light assemblies are hanging loose.

5. Twist the black bulb holder one quarter turn on the back of the assembly and pull, this separates the weather cover from the bulb.

6. Push the bulb down against the spring and then pull back out, it should separate relatively easily.

Note: Total time was about 5 minutes to replace two bulbs. The specs call for #194 bulbs. Check your local auto supply; I paid $1.56 for two bulbs. With the bolts in place but loose they will slide right in, following these directions in reverse. These directions work on all Impalas made from 2000 through 2005.

JR

The engine in a 2002 Ford Focus typically comes out from the top of the car during removal and replacement procedures. This process involves disconnecting various components such as the wiring harness, hoses, and motor mounts before using a hoist to lift the engine out from the engine bay. Removing the engine from the bottom would require extensive disassembly of the front suspension and subframe, which is not a standard practice for this vehicle model.

I recently added freon to the low pressure side of the system. The port is located under the passenger side fender. You need to remove the, then take 2 fasteners off the front edge of the fender liner. You'll find the well hidden low pressure charging port there.

All O2 sensors are screwed into the exhaust system. Follow the exhaust pipes from the engine rearward and you will find them all.

Remove the covering under the glove box. Disconnect the power to the blower. The blower motor is fastened to the ductwork with 3 screws.

Parfocality is the term used to indicate that when an object is in focus at low magnification, it will also remain in focus at higher magnifications without the need for refocusing.

2588 to 2617 pounds = 1176.4 to 1189.5 kg.

Shift light, maybe? If it comes on around at a certain RPM every time, that'd be my guess.

It sounds like there could be an issue with the alternator or the electrical system in your car. The drop in idle speed and juddering indicate a potential problem with the engine. The flickering interior lights and headlights suggest an issue with the alternator not properly charging the battery. It's best to have a mechanic inspect and diagnose the specific cause to address the problem correctly.

A bubbling noise when accelerating on a Mercury Topaz 1990 could indicate a problem with the cooling system, such as air bubbles in the coolant or a leak. It is recommended to check the coolant level, look for any visible leaks, and consider bleeding the cooling system to remove air pockets. If the issue persists, it's best to have a mechanic inspect the vehicle.

The fine focus knob is used to bring an object into fine focus, while the course focus knob is used to bring an object into approximate focus. The course focus knob should only be used on the low-power and scanning objectives of the light microscope. Using it on the high power microscope is okay, but you should be very careful. It is no recommended to use the course adjustment knob on the oil-emersion objective as it is so close to the stage and could lead to a potential break in the slide. Fine focus adjustment knob is useful to bring out the fine details in the specimen on your slide. Can be used on any of the objectives, but most receptive on the high-power and oil-emersion objectives.

If the knob on your 2004 Ford Focus's AC system is not turning on the air conditioning, it could be due to a faulty switch, a blown fuse, a defective compressor, or low refrigerant levels. It's best to have a qualified mechanic diagnose and repair the issue to restore proper functionality.

The 2000 Ford Focus is a compact car known for its practicality and fuel efficiency. It offers a comfortable ride with good handling, making it a popular choice for daily commuting. Keep in mind that older models may require more frequent maintenance due to wear and tear.

Possible reasons for freon not flowing into the low-pressure port during a recharge could be a blockage or restriction in the system, a malfunctioning metering device like the expansion valve, or an issue with the compressor not creating sufficient suction. It's important to diagnose the problem accurately to ensure a successful recharge.

The speed regulator for a 2002 Ford Focus is typically located within the Engine Control Unit (ECU). Attempting to modify the speed regulator to make the car go faster is not recommended as it can void warranties, compromise safety, and may be illegal. If you are looking to increase the vehicle's speed, consider professional performance upgrades or enhancements.

the reason the throttle would be sticking on your focus is that it (the actual unit) could be dirty. or the throttle cable could have dirt in its casing. what you need too do is remove the throttle cable and spray engine degreaser in the casing and hang it up too let the dirt and grime drip from it. be sure to use wd-40 to relubricate the cable. now as of the throttle body do the same thing. but use a non abrasive cloth and wipe the unit clean. make sure there is no dirt in any small cracks or crevises.

write down how the belt is currently installed loosen the tensioner with a 15 mm socket it is the last pulley on the far bottom left you must remove the passenger wheel and splash guard to get to this pulley after you loosen the pulley pull the belt off put on the new one in the same order i go over the alternator last usually make sure the belt is on all pulleys tight and off you go it is easier to get the belt on with 2 people time .5 - 1 hour