On the 1.8 DOHC GSi model the cam shaft timing sprockets have little marks along the edge of them. The two marks MUST be lined up closest to each other. The marks are very small and you may want to use your fingernail to find them. On the 1.6 SOHC model, the camshaft timing sprocket has the same type mark, but it must be at the 9 O'clock position. It should be EXACTLY on the top plan of the cylinderhead mating surface with the valve cover. On all Storm engines, the lower crankshaft timing sprocket has a small notch. That MUST be at the 12 O'clock position. It will line up with a small little triangle on the oil pump housing.
Your best shot would be attempting to outrun it of course. But that's just the basics.
If there is shelter nearby (a cabin, etc) run inside it and just hope you'll live.
The best protection is to live very far from volcanic mountains, but this is not always possible. The next best action is to prepare for evacuation (with more than ONE route) if a situation develops. Roads and bridges are easily rendered impassable by debris or masses of vehicles.
In the immediate area of the volcano, eruptions can be survived indoors by preventing ash inhalation, and by watering rooftops that are exposed to hot cinders. The advance of lava can also by slowed by water, but often with negligible effect. Again, prompt movement away from the paths of volcanic debris or gas emissions is crucial in an actual eruption.
It' Really quite easier that it looks,I've had to do it myself. 1. Remove the wheel. 2.Remove the center nut from the axle. 3. Remove the brake assembly and rotor.(do not remove the brake line) 4. Remove the ball joint from the A frame and the two bolts on the bottom of the ball joint and slide it out,might be kinda tough, because of the pressure of the strut which you should be able to compress. 5. Put a oil pan underneeth the transmission and line up the shaft with the tranny, and pull it out as straight as possible, because it just has a snap ring on the end. YOU WILL NEED ONE QUART GEAR OIL.
A ball joint fork makes it much easier to pop the axle out. To pop it back in, make sure the missing part of the snap ring is at the BOTTOM, and then just try to pop it in by hand by repeatedly lunging it at the differential until it goes in.DO NOT use gear oil use 5W 30
hire a mechanic! Or if your mechanically inclined here's a brief overview. be forewarned this took me 20 hours with a helper who performed three clutch replacements.Your primary goal is to remove the transmission because the clutch is located between the transmission and the engine block.
Remove the air filter housing, radiator hoses, clutch slave cylinder, vehicle speed sensor, starter, and axle. disconnect any electrical connections on the transmission and also the shifter cable linkage. disconnect the exhaust pipe at the gasket near the bottom of the radiator, and also a bracket near the sub frame. the exhaust blocks access to two of the three engine mounts that you need to remove. first support the engine from above then remove the following engine mounts: first location is under the air filter housing, second is near the bottom of the radiator near the center engine support, third is at the intersection of the exhaust, center engine support, and sub frame. the sub frame must be lowered slightly to remove the engine mount. all the bolts for sub frame are huge and high torque so an impact wrench is highly recommended.
At this time the engine should be fairly loose and you should have access to the transmission. there are three bolts that thread into the transmission bell housing side and four that thread in from the rear of the engine block. remove all. a jack should be used to support the weight of the transmission as you drop it and slide it out from the drivers side of vehicle.
Behold - the clutch! (which will be on the engine ) replace the worn clutch and reassemble everything in reverse. Be sure to replace all your fluids and to bleed the clutch line to the slave cylinder. HAVE FUN!!!
The question you ask is too involved for a proper answer. You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
It is the first storm/typhoon warning said in the TV news broadcasts when the local weather bureau (PAGASA) detects a storm. Normal classes usually are in service still.
Signal No. 1: Mild to strong winds
Signal No. 2, 3 and 4: Cancellation of classes due to flooding and strong winds
Dead means "no longer living", "hated to the point of ignorance by another party", amongst many other senses.
i had this problem for a long time. came to find out that it was the plug on the back of the alternator was loose. the rubber band around the plug had got worn down so i actually got so new bands at advance auto it solved that problem. also alt. belt may be loose too.
Check the alternator.
Stick or auto? with a stick, the motor hesitates if any thing. with an automatic, check your fluid level, the color of it should be a redish pink. don't overefill. If color is sortof black or brown then change fluid and filter for tranny.
The Fuse size is listed on the under side of the Fuse Cover.
It produces it's own energy source by being wound-up by a person. It saves the person money; battery operated radios would be expensive to run. It can be used in remote areas without electricity. It keeps people in remote areas up-to-date with what's going on outside of their area.