0
GM and GMC
This category covers questions about General Motors and its second best-selling division, General Motors Company (GMC). General Motors currently has four main divisions in the United States: Buick, Cadillac, Chevrolet, and GMC. General Motors was founded in 1908 and employs over 200,000 people, with its headquarters being in Detroit, Michigan.
3,195 Questions
How many quarts of oil needed for oil change for a 2009 gmc serria 5.3 liter engine?
buy 7, they hold about 6.5
How do you reset oil light on 2005 C5500?
Turn your key to on, not run, and depress the gas pedal five times slowly but within a few seconds. You should hear a chime, the change engine oil light will go off when u start the vehicle again if it doesn't go off when it chimes
The General Motors Company (GM) is a United states-based automaker with its headquarters in Detroit, Michigan.
Where is the purge valve solenoid on a 2007 gmc canyon?
On the engine near the starter. It is accessible by removing the driver side front wheel and inner skirt.
How do you replace ign lock cly on 1999 gmc pickup key will not turn?
- Set the front wheels in the straight-ahead position.
- Set the steering wheel in the LOCK position.
- Disconnect the negative battery cable.
Caution: When you are performing service on or near the SIR components or the SIR wiring, you must disable the SIR system. Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.
- Disable the Supplemental Inflatable Restraint (SIR) system. See: Air Bag(s) Arming and Disarming\Service and Repair\Disabling the SIR System
- Remove the tilt lever.
- Remove the 2 TORX head screws from the lower steering column shroud.
- Remove the lower steering column cover shroud from the column.
- Remove the TORX head screw from the upper steering column shroud.
- Remove the upper steering column shroud from the column.
- Turn the ignition lock cylinder to the START position.
- Using an awl, insert the tip into the ignition lock cylinder access hole (1).
- Push down and hold the ignition lock cylinder retaining pin.
- Release the ignition lock cylinder to the RUN position.
- Remove the ignition lock cylinder by pulling the ignition lock cylinder away from the steering column (2).
INSTALLATION PROCEDURE
- Install the ignition lock cylinder into the steering column (2) using the following procedure:
- Install the upper steering column shroud to the steering column.
- Install the TORX head screw to the upper steering column shroud.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
- Tighten the screw to 1.5 Nm (115 inch lbs.) .
- Install the lower steering column shroud to the steering column.
- Install the tilt lever.
- Install the TORX head screws to the lower steering column shroud.
- Tighten the screws to 3 Nm (25 inch lbs.) .
- Enable the SIR system. See: Air Bag(s) Arming and Disarming\Service and Repair\Enabling the SIR System
- Connect the negative battery cable. Perform the Idle Learn Procedure. See: Testing and Inspection\Powertrain Control Module (PCM) - Idle Learn Procedure
Perform the PASSLOCK Reprogramming Auto Learn. See: Testing and Inspection\PASSLOCK - Reprogramming Auto Learn
What is the stock market symbol for general motors and target stores?
General Motors Corporation has not been publicly traded due to its former liquidation state.
(see related questions)
Target Stores trade on the NY exchange as TGT (Target Corporation).
If you are referring to a vehicle you put a 50/50 mix of distilled water and coolant in the radiator and overflow resivoir. You also put distilled water in the battery if it is not sealed. Also the windshield washer resivoir holds washer fluid which is part water.
86 gmc pickup with carb smokes when cold start and idles real rough until warm?
The vacuum pull off for the choke on the carburetor may be bad or out of adjustment.
What is the average payload capacity of an 18 wheeler trailer truck?
Between 21 and 25 tons. 23 to 24 would probably constitute the majority.
Where does General Motors belong to?
General Motors belongs to the stockholders. It is an independent company.
Where does the speedometer cable hook to transmission on 1990 gmc?
Check the side around the tailshaft.
To relieve pressure in the brain caused by fluid buildup.
WHERE IS THE 1987 gmc s15 truck fuse box?
The fuse block is located below to the right of the steering wheel, just above the parking brake.
- Open in Google Docs Viewer
- Open link in new tab
- Open link in new window
- Open link in new incognito window
- Download file
- Copy link address
- Edit PDF File on PDFescape.com
What is the checking level cold procedure for the Allison LCT 1000?
According to the service manual, it says to check the fluid with the engine idling in Park. There is a cold engine range of marks and a hot engine range of marks on the dipstick.
The upper set of marks are for the hot engine level range and the lower for cold check.
The fluid expands when it is heated.
Can a 350 bored 060 over be used on the steet?
Yes it can, but use extra cooling as it will overheat when at long stop lights or stop and go traffic.
Is Chevrolet or GMC the higher end?
A GMC will usually cost slightly more than a Chevrolet. In reality a GMC is just a rebadged Chevrolet. All drivetrain parts are interchangeable between the vehicles.
What is the Gas mileage on 1979 gmc camper special?
I have a 1979 gmc camper special with a fairly heavy nine and a half foot camper on it. I get 10 miles to the gallon maybe 11 with a tail wind.
How do you change a headlight in a GMC acadia?
On the 2009 model, the genius engineers at GMC decided to make you access the rear of the headlamp assembly through the wheel well. This involves removing 11 screws from the plastic shield in the wheel well. You will need to start the car to turn the wheel to get the clearance for your screwdriver to remove these screws. The plastic shield will not come out even with these 11 screws removed, it just bends enough to get your arm in there. Then you get to blindly feel for the cap at the back of the headlamp assembly that needs to be unscrewed. Then you get to blindly feel for the back of the lampholder and try to give it 1/4 turn to release it. Then you get to hold a flashlight in your mouth because you will need both hands to release the metal tabs that are holding the bulb in the lampholder. All the while the plastic shield will be pinching and scraping the skin off your forearms. The real joy comes when you get to try to put the new bulb in the holder and get the lampholder to seat itself in the assembly and snug it up with the 1/4 turn.
Thank you GMC engineers, instead of replacing another bulb tomorrow I'll just poke pencils in my eyes to experience equal pain.
How much oil does a 1997 gmc surburban 5.7 engine take?
5 is the most common, there are few that take 6 but very few.
