Mazda

its junk

Clean contacts group under the passenger seat

If you are facing the distributor cap from the passenger side, starting at nearest to the front of the truck and going clockwise the sequence is 1-3-4-2. The timing check page below illustrates this.

There are 2 ports, the one that you plug your OBD II scanner into is under the drivers side dash, the second one is in the engine bay near the fuse box and drivers side front headlight.

A shop in Port Orchard, WA says yes

121 hp

Trouble code P0421 means: Catalyst Efficiency Below Normal (Bank 1)

torque spec for automatic transmission pan bolts = 96 to 120 in-lbs. - Haynes Repair Manual #36071, 1993-2005 Ford Ranger and 1994-2005 Mazda B-Series Pick-ups

IF you have a trouble code or a "Check Engine" Light, it can take a several minutes or so. Best to do some highway driving. OR, just take the battery terminals off to clear the computers memory. If it stays on, goto AUTOZONE and ask for a free trouble code reading (AKA O.B.D). They can tell you what is wrong, and clear the computer for you manually. CODEBLU

Just goto a parts store (AUTOZONE, OREILY's, NAPA, etc). Find the aisle with the wiper blades. Normally will be a book that you can look up the size if you know the year and make of your vehicle. If you can't find the book, or you are uncomfortable, just ask a store associate who can look it up for you in the book or, on their computer. You could call them ahead of time, and they can set the right ones aside for you to pick up and pay. They can even put them on for you too.

Odds are, your tank sensor itself is not working properly. I recently had that problem myself. If you don't have much fuel in the tank, move everything out of the way, drop the tank, and on top, you'll see an oval-ish spot on the top with 2 wires and 2 hoses running to it. Unscrew it and pull it out. On it will be a little galvanized steel plate. bend the ears on it to remove it. There will be a metal arm that rubs against a bunch of copper coils. You can either try to bend just the arm, so it rubs against the coils again.... Or just bend the housing a tiny bit so it does the same. Then, stick the cover plate back on, screw the assembly back in the tank, and re-install it.

how do u replace fuel injector on 2001 b3000

while pedal is depressed fully, OPEN the bleeder screw on slave cylinder until fluid has stopped squirting out. CLOSE screw while pedal is still depressed. let pedal rise to full height and repeat these steps until flow from slave cylinder is just fluid and no air bubbles.it should take no more than a couple of repetitions as it is a very short run of tubing thus holding less than an ounce of brake fluid. you need two people to do the procedure-one in the truck and one under the transmission.

quick, stock mazdaspeed is 13.7 1/4 mile with good driver.

If you checked the switch, fuse and bulbs the only thing it could be is a open ground. Find the ground wire on the bulb socket and check for continuity. With a tester put one wire one the ground at the socket and the other on the neg. battery terminal

First, read the owners manual. Second, do what it says. The driver's side requires a cover be removed to access the backs of the bulbs. For the low beams, remove the electrical plug by squeezing the tabs on the sides of the plug and pulling. Then remove the rubber seal by working it off the housing. The "tricky" part is next. Take a good light and examine the layout of the assembly so the rest of this makes sense. The bulb holder is held in place by a wire bail with a curved piece toward the top. One has to press the curved loop toward the front of the car and apply upward pressure once the wire end is off the metal tab that normally holds the wire tight against the bulb holder. This is easier than it seems. Then pull the wire backward - it is hinged on one side of the housing - and swing it out of the way. Carefully pull the bulb holder / bulb from the housing. Remove the bulb from the holder by prying it out of the holder. Dispose of properly. Place the new bulb in the holder without touching the glass. Place holder/bulb in the housing with the tab oriented to the slot toward the top of the housing. Swing the wire back over the holder and press toward the front then down to replace the end of the wire behind the tab. If the holder moves at all, you don't have the wire secured properly. Replace the rubber seal making sure it is tight on the housing and on the bulb holder. Replace the electrical plug until it pops into place.

i have a b2200 Mazda 1993 and everytime i brake a clicking noise come out of the passenger side like in the back of the seat at the same time the brake pedal moves down with each click what can that be.

Take out one of the key barrels - from either doors or trunk lid and you should find it on the lock cylinder itself.

Disconnect the positive cable then turn your key 3-4 times then reconnect the positive cable and start the car. You may have to reset your windows after that so you will put the windows down when you put them up hold the the button till you hear it click.

If the lever to fold down the rear seats in a Mazda Demio has become detached from the cable, it is possible to fix this by opening up the area of the seat where the lever should be. There should be a small plastic plate in the area protecting the lever from moving too far up or down. This plastic piece is either screwed in or is held in by clips. Remove the screws or clips and reach in to find the cable. Pull the cable up, insert the lever into the opening and connect it to the cable. Then close the seat back up.

ignition timing is controlled by the electronic control module or the "brain" on distributorless engines. Reysher

I own a 2002 Mazda B-2900 pick-up (Japanese model) that uses the 2.9 litre "WL" turbo diesel engine.

Yes. Starter/Bellhousing issues

Jujiro Matsuda was the founder of Toyo Cork Kogyo. The name "Mazda" was

coined when the company first produced automobiles. "Mazda" is the

Zoroastrian god of life. I believe the name was chosen to represent the

company's ever moving innovations. It was also done so because "Mazda"

closely resembles "Matsuda". Mazda is pronounced MA-TSU-DA in Japanese (the

language lacks the "Z" sound). You may sometimes find candles with the name

"Mazda" on them. They're related to the actual Zoroastrian religion and not

the motor company. You should now understand why the Mazda logo from the

early 90's were used and scrapped due to its difficulty to be recognized.

The logo did hold meaning, and is actually a symbol of a burning candle.

follow the clutch line down to the trans and there is a coupler that is about twice the size of the line and there is a little greyish white ring on the line side pused it squarely towards the coupler till it is all the way in the coupler then pull the line out