0
Mercury Mountaineer
The Mountaineer was a five-door mid-size SUV manufactured by Ford Motor Company from 1997 to 2010. The vehicle was known for its stability and superb handling, and features a front engine rear-wheel drive layout.
1,435 Questions
What type of brake do you use for your 2000 mercury mountaineer?
DOT ( 3 ) brake fluid , if that is what you are asking ?
What is the spark plug gap for a 2002 mercury mountaineer?
is 54 gap for a spark plug mercury mountanier 2002 4.6
Which freon do you use in a mercury mountaineer?
Since the first model year of the Mercury Mountaineer is
the 1997 model it would be ( r134a )
Where is bank 2 sensor 2 on a mercury mountaineer?
Bank 2 is the drivers side of the engine in your Mercury Mountaineer
Sensor 2 is in the exhaust after the catalytic converter
Mercury mountaineer power windows?
Depending on the age of the Mountaineer, they all come with power windows now. The driver has control of all 4 windows and can also lock them so other passengers cannot roll up or down their window.
How many quarts of oil is needed for a 2004 mercury mountaineer?
According to the 2004 Mercury mountaineer Owner Guide :
With engine oil filter change :
The 4.0 liter V6 takes ( 5.0 U.S. quarts of 5W-30 engine oil )
The 4.6 liter V8 takes ( 6.0 U.S. quarts of 5W-20 engine oil )
Where is the speedometer sensor on a Mercury Mountaineer?
where is the location of the vehicle speedometer sensor on a 99 Mercury Mountaineer
Why is the theft light blinking on my 2002 Mercury Mountaineer and it will not crank?
had to replace the battery in my 2002 Mercury Mountaineer but now the theft light is blinking, it is cranking up. How can I stop it?
What does the code p0401 mean on a 2002 Mercury Mountaineer?
Trouble code P0401 means:Exhaust gas recirculation flow insufficient detected
Where is the pcv valve on a Mercury Villager and how do you get it out?
The PCV Valve is located right beside the EGR valve (located in behind but attached to the intake manifold) and has a thick black tube connected to it, when that tube is removed, it will expose the PCV valve from there, you will have to unscrew it and replace it, then re connect the hose and start it up! Trust me it sounds a lot easier than it really is! It takes almost 90 mins to reinstall! I am not sure it will work on all Villagers!
On a 2000 Villager, the PCV valve is pressed into a rubber grommet on a 90 degree tube extension from the rear valve cover, which is then connected by a black hose to a nipple extension on the upper rear intake manifold. The way to remove it is to unbolt the bracket attached to the intake manifold holding the accelerator cable, using 'right angled' pliers to open, then push the hose clamp back from the end of the hose attached to the intake manifold, then using the angled end of a brake shoe adjusting tool to push off the hose from the nipple on the rear upper intake manifold, being careful not to break off this nipple (the upper intake manifold is molded plastic and the nipple is part of the manifold). Once this end of the hose is loose, then the PCV valve with the hose attached can be pulled out of the grommet from the valve cover end.
It helps to place a little silicone grease onto the manifold end of the hose and the base of the PCV valve that slides into the grommet for ease of future removal. Replace the hose clamp, replace the accelerator cable bracket, and you're ready to go. Make sure you do this with the engine cold, because there isn't a lot of room in the back of the engine. It took about 10-15 minutes to do it this way.
What is causing the heater to blow cold air in 2002 Mercury Mountaineer?
you would have to see a mechanic about that problem
Where can you find transmission diagrams of a 2002 Mercury Mountaineer?
how do you change the transmission pump in a 2002 mountaineer
Where do i find the air ride switch in a 99 Mercury Mountaineer?
I believe the on / off switch for the air suspension system is in the cargo area , on the drivers side , behind the removable plastic panel where the wheel jack is located
How do you fix inside door handle 2000 mercury mountainer?
you have to enter through the rear hatch window... then have someone else open the hood and disconnect the battery. after that you use your cell phone and dial-up the local dealer and tell them you are locked in... They will send someone straight away and fix your door
Where is the transmission dip stick located in Saturn sl2?
Dipstick and tube is located just to the right of the intake and airbox (air filter) just right of car center, it has a yellow handle, and right of oil dipstick in the middle of engine bay.
Where is the factory keypad entry code located on a 2001 Lincoln Continental?
usually on the trunk hinge
My bright lights come on when you turn the right turn signal on 2005 mercury mountaineer?
I'm not a mechanic / technician but my money is on the multi-function switch
inside the steering column cover ( the turn signal lever sticks out of the
cover and is used to turn on the high beam headlights )
Over the years I've had a Ford that every time I would use my signal lights, and
it was raining my windshield wipers would stop ( very scary at night when it
was raining and I was signalling a turn at a corner )
I had another Ford where the windshield washer squirter button didn't work
until it was pushed at least three times and a couple of the intermittent
wiper positions stopped working
How do you reset a mercury mountaineer after new battery and alternator?
If you remove the battery or break the connection to it, you have reset it. That is why the presets on the AM/FM radio disappear.
The question is how. You do not have to reset anything except the radio presets and the clock.
How do you disable the alarm on 2002 Mountaineer?
We do not provide information that could be used to commit criminal acts. If it is your vehicle, check with the dealer service department.
How do you reset tire pressure light on 2005 mercury mountaineer?
1. Make sure all tires are inflated to the vehicle's recommended inflation pressures (found in the owner's manual on the door placard).
2. Turn the ignition switch to OFF then press and release the brake pedal.
3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds.
4. Press and release the brake pedal.
5. Turn the ignition switch back to OFF.
6. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds.
7. The horn should sound letting you know the vehicle has entered into TPMS relearn mode
8. Place the VT10's antenna on the sidewall of the driver's side front tire 180 degrees from the valve stem.
9. Hold the right button of the VT10 triggering tool for 5-10 seconds. The vehicle's horn will sound letting you know the sensor has been learned.
10. Once the horn sounds, move on to the passenger side front tire and repeat the process. Each tire should only take 30 seconds.
11. After the passenger side front tire has been learned, continue on to the passenger side rear tire and finishing with the driver's side rear tire.
12. You may now turn the ignition to OFF. If the horn does not sound, the sensors were learned successfully. If the horn sounds twice, then the process must be repeated because there was a malfunction.
How do you remove a harmonic balancer from a 2005 Mercury Mountaineer?
You must first find a very large telephone pole or concrete building, wrap a large chain around the harmonic balancer and attach it to the building or pole, now be very careful not to start the car at this point as you might damage your vehicle. find another large vehicle preferably a large pick up with at least a class3 hitch. attach this vehicle to your vehicle with a large chain prefereably at least 20 feet long. after attaching everything and making sure all is secure, very carefully and safely accelerate the pull vehicle to 30 miles per hour, the force applied should be suffiecint to remove that stubborn harmonic balancer, if one try does not work repeat. I have never tried this technique but I have been told it works. good luck or you could go see a mechanic if in doubt!
How do you locate the driver's side keypad code on a 2005 Mercury MONTEGO?
Most vehicles come with the code on a sticker on one of the Trunk Life Rods. Some owners remove this tag, some don't. Some put it inside the glove box and some write it in the Owner's Manual. If it's not in any of these places, you're only choice is to go to a dealer and have them request the master code for you.
When do you use overdrive on a 2001 mercury mountaineer?
Overdrive is the normally allowed position
It won't shift into overdrive until the speed is higher anyway ( such as on the
highway / freeway )
If you are towing something , or are driving in hilly country where the
transmission is constantly shifting between overdrive and drive , you want to
switch the overdrive off using the switch on the end of your gear selector
lever ( P R N etcetera , the O/D OFF light will appear in your dash )
