0
Oldsmobile Ciera
Manufactured by General Motors from 1982 to 1996, the Ciera was a mid-size car and the best-selling model of Oldsmobile. It was offered in 2-door sedan, 4-door coupe and 4-door station wagon body styles.
697 Questions
How can you identify where the low side service port on the AC system of a 1995 Oldsmobile Ciera?
Can't say from experience but they're generally up from near your condenser or near the firewall. If all else fails, find your AC compressor and trace your lines backwards.
How do you change out the flasher relay and where is it located on a 1993 Oldsmobile Cutlass Ciera?
To replace the cylindrical flasher relay, pull out the ash tray to its fullest, and remove the top two bolts inside, one on each side. Push the ash tray mostly in so you can access the bottom two bolts, one on each side. Pull out and lower the ash tray until the tube-looking bulb in the center, which is hidden behind the panel, appears. Don't pull out too far, as wires still connect this bulb. With a pliers, grab the left plastic side of the bulb where the wires connect, and slowly twist away from you, pulling out at the same time, until the bulb is freed. Lower the ash tray rear and pull a bit to the left until the cylindrical flasher appears. It is clamped to the very right side end of the ash tray. Pull it out of its clamps. Remove the flasher from the pair of wire plugs. You may have to use a regular screw driver to jimmy them loose. Replace the flasher. Reverse the process.
under dash on drivers sideOn my 87 Cutlass Ciera it was located under the dash, fairly close to the steering column. I had to remove a section of plastic to get at it. I changed mine out a few years ago so cant remember in any more detail where it was.93 Olds Cutlass Ciera (Canadian)
Had the emergency flasher fail on my Ciera. Found it behind the glove box on
the passenger side of the car inside a brown coloured cover (about 3 in long,
2.5 in high and about 1.5 in wide). The turn signal flasher was mounted on the passenger side of the fuse box - you can see it when you remove the glove box. Hope this helps someone.
Where is the temp sensor for 93 olds cutlass ceirra 3.3?
The temperature sensor on a 93 Olds Cutlass Cierra 3.3 is located on the back of the engine. It is on the intake manifold.
Antenna motor keeps running when antenna is shut off killing the battery What do you do?
The wiring diagram ahows that the power feeds the motor all the time but its turned on by connecting the negative side on thru a relay. if a short is found in the wire and it grounds out then the motor will try and run. So either a wire is grounded between the antenna and the relay. Or the relay could be bad.
Does the a c compressor use flat washers or o rings for 1993 Olds Cutlass Ciera S V6 3.3?
On the 1993 Oldsmobile Cutlass Ciera S ,V6, 3.3 some of the AC Compressors had O Rings & others used flat washers. That Year they used some with O rings & some with flat washers. I called the Chevrolet Dealer where I bought mine & that is what they told Me. The Auto Parts place said the same thing. You have to look at Your old Compressor to tell. Mine has the Compressor with flat washers!!
Where is the power window control module located on a 1994 Olds ciera?
had the same problem this week..called the local olds dealer...parts tech claims it is located under the dash between steering column and kick panel......i would love to see a picture of this "animal" as there are soooo many connectors and wires it would be so much easier to indentify
Where is the location of the heater blower relay on a 1989 Olds Ciera SL with a 3.3L engine?
On 1993 Ciera 3.3 V6 the heater blower relay is located inside engine compartment, just behind right front headlight area. There are 4 or 5 relays there. Use wire colours to determine which relay goes to heater motor.
Relay part can be separated from the wiring system. Inside it you will see the male connectors - the power connector may be burned. The female connectors are in the other half and are attached to wires going to the heater blower. Check the female connectors to ensure they have not been heated and melted by the faulty relay. If they have they need replacement too.
The male relay is easy to replace - most auto parts stores will have this part and it is a "plug and play" fix.
The female end with the wires going to the heater is another story. It is part of a large wiring harness, which is usually only available at a dealer. If this part needs replacing too, consider going to wrecking yard and just cut one off a wreck and splice it in onto your car. Break it apart from the old relay at the wreckers to make sure it hasn't been burned inside by a faulty relay. If it has keep going to the next wreck until you find a good one.
Always replace the relay itself with a new one. Don't trust an old one from a wreck. Cost will be around $50 and well worth the piece of mind on the highway on a cold winter day.
How do you remove the factory radio from a 1990 Olds Cutlass Ciera?
To remove the radio. 1. remove the ashtray, and 2 corner vent diffusers. There are bolts to remove in ashtray area and inside Left/right most vents. 2. remover the rubber steering wheel trim ring. then remove the whole vent diffuser assembley. 3. remove the 4 screws at the top of the instrument cluster. and the 4-5 at the bottom. (covered up by the vent piece).
I have read a common problem with the 90-93 Oldsmobile cutlass is that the ground on the shift silinoid can cause it to lose 3rd and 4th gear, I am trying to figure out where it is located.
Please if you know email scott@moteladvertising.com
Where is the flasher for the blinkers on a 2002 Camaro Z-28?
"The turn signal flasher, a small cannister-shaped unit located under the dash, in a clip to the left of the steering column...to replace the flasher, simply unplug it and pull it out of the clip...installation is the reverse of removal." -Haynes Manual
Were is the turn signal flashers located on a 1990 Cutlas ciera?
It has 2 flasher relays.
The turn signal flasher relay is located on the drivers side under the dash, mounted on the upper passenger side of the steering column support.
The hazard flasher relay is located on the drivers side, under dash, above kick panel, mounted on bottom of convenience panel.
Where is the blinker flasher for the Oldsmobile ciera 1996?
It is located just above the ashtray and below the radio, somewhat to the left side. It has sufficient wiring to be pulled down to change it, if now you need to remove some of the paneling, which is a time consuming process. In a perfect scenario, all you would need to do it pull out the ash tray, remove the frame above it, then reach up or see the flasher unit (it is about half the size of a 35mm film canister), then swap it out.
Why is your oldsmoblie cutlass cerria backfiring?
More than likely it is out of time. Have the timing checked. If you have changed the plugs or plug wires, you have them hooked up wrong.
Need wiring diagram for cooling fans for 93 Mercury Capri?
You can find the wiring diagram for the 1993 mercury capri at the following site. This manual is very acurate for all the things pertaining to the 90's capri. www.techcapri.com This site has just about everything you need for this little car. Good luck.
Why is my oldsmoblie cutlass cerria backfiring and not starting?
timing out of adjustment. start with distributer timing and go to timing belt or chain
could be the crank position sensor located behind the harmonic balancer
Your Oldsmobile cutlas will not start or turn over?
Does anything else electrical work? Horn, lights? If not, the battery may be dead. If other electrical stuff works, the battery may have an open cell, which would cause it to be unable to turn the starter. Or, it could be a blown fuse somewhere, or a loose/dirty battery cable, a bad starter, there are many possibilities. Most auto parts stores will test batteries for free. Take the battery out and have it tested...that's a good starting point!
How to replace dimmer switch 1991 olds cutlass ciera?
You will need to disconnect battery, remove horn pad, pull steering wheel with wheel puller,remove some dash plastic, and once you are that far it is a matter of removing a few torx fasteners, dropping the column, ( two bolts) and feeding the harness down. Basic tools. It may sound harder than it is; it's not that bad. Good luck.
