Oldsmobile Cruiser

Yes, a three-quarter front bench seat can be fitted to a 2009 Toyota Land Cruiser Wagon, but it may require modifications or specific aftermarket parts to ensure proper installation and safety compliance. It's essential to check with a professional installer or automotive specialist to confirm compatibility and ensure that the seat meets safety standards. Additionally, consider the vehicle's interior space and passenger comfort when making this modification.

If a 1985 Oldsmobile Cutlass won't hold a charge despite having a new battery, alternator, starter, and terminals, the issue may lie in the wiring or electrical connections. There could be a short circuit, ground issue, or faulty ignition switch draining the battery. Additionally, parasitic draws from accessories or lighting circuits could be consuming power when the vehicle is off. It's essential to conduct a thorough electrical inspection to identify the source of the problem.

On a 1987 Cutlass Ciera Cruiser, the rocker cover is located on top of the engine, covering the cylinder head and the valvetrain components. The PCV (Positive Crankcase Ventilation) valve is typically found on or near the rocker cover, often integrated into the cover or connected via a hose to the intake manifold. You may need to remove the air cleaner assembly to gain better access to the PCV valve.

On a 1993 Oldsmobile Cutlass Cruiser, the keyless entry module is typically located in the driver's side door. It may be found inside the door panel or behind the dashboard, often near the steering column or under the dash. For precise location, consulting the vehicle's service manual or a repair guide specific to that model may provide additional details.

To remove the battery from a 1989 Cutlass Ciera, first, ensure the vehicle is turned off and parked on a flat surface. Open the hood and locate the battery; then, use a wrench to disconnect the negative (-) terminal first, followed by the positive (+) terminal. Once both terminals are disconnected, remove any securing brackets or hold-downs, and carefully lift the battery out of the tray. Always handle the battery with care and dispose of it properly if needed.

To unlock the radio in a 1995 Oldsmobile Cutlass, you typically need the radio code, which is unique to each vehicle. This code can often be found in the owner's manual or on a card that came with the vehicle. If you cannot locate the code, you may need to contact an Oldsmobile dealer or a qualified automotive technician for assistance in retrieving it.

Yes, some 1987 Oldsmobile Cutlass Salon models were offered with a factory-installed sunroof as an optional feature. The availability of this option may vary based on the specific trim level and packages chosen by the buyer. Typically, sunroofs were more common on higher trim levels or as part of specific option groups.

To connect the battery cables to a 1992 Oldsmobile Cutlass, first ensure the vehicle is turned off and the keys are removed. Connect the positive (red) cable to the positive terminal of the battery, ensuring a secure fit. Next, attach the negative (black) cable to the negative terminal of the battery. Finally, double-check both connections for tightness before starting the vehicle.

To remove the battery from a 1994 Cutlass Sierra, first ensure the vehicle is turned off and the keys are removed. Open the hood and locate the battery, then disconnect the negative terminal (usually marked with a minus sign) first, followed by the positive terminal (marked with a plus sign). Once both terminals are disconnected, remove the battery hold-down bracket or strap, and carefully lift the battery out of the tray. Always handle the battery with caution due to its weight and potential acid hazards.

The black box next to the battery on your 1994 Cutlass 3.1L is likely the fuse box or a relay module, and loose wires can cause poor electrical connections. This can lead to intermittent issues with starting the car or stalling while driving, as the electrical components may not receive consistent power. It's important to inspect the connections, repair any loose or damaged wiring, and ensure the fuses and relays are functioning properly to resolve these issues.

Pontiac and Oldsmobile motor mounts are not necessarily the same, as they were designed for different vehicle platforms and specifications. While some mounts may be compatible due to shared components across GM brands, it's essential to check the specific model and year for compatibility. Always refer to manufacturer specifications or consult a professional to ensure proper fitment.

In the Oldsmobile Ciera Cruiser Wagon, the cigarette lighter fuse is typically located in the fuse box, which is usually found under the dashboard on the driver's side. You may need to consult the owner's manual for the exact fuse number and location, as it can vary depending on the model year. If the lighter is not functioning, check the corresponding fuse and replace it if necessary.

If your 1991 Cutlass Cruiser wagon won't stay started and keeps cutting off, it could be due to several issues. Common causes include a faulty fuel pump, clogged fuel filter, or issues with the ignition system such as bad spark plugs or a failing ignition coil. Additionally, problems with the air intake or a malfunctioning sensor, like the mass airflow sensor, could also lead to stalling. It's best to run a diagnostic to pinpoint the exact cause.

On a 1989 Oldsmobile Custom Cruiser wagon, the fuel pump is located inside the fuel tank. To access it, you'll typically need to remove the tank from the vehicle, as the pump is not externally accessible. Ensure to take proper safety precautions, such as relieving fuel system pressure and disconnecting the battery, before attempting any repairs.

To install a Holley carburetor on an Edelbrock Performer intake, first ensure the intake manifold is clean and free of debris. Use the appropriate gasket for the Holley carburetor and align it with the mounting holes on the intake. Secure the carburetor on top, tightening the mounting bolts evenly to avoid warping. Finally, connect the fuel line and any necessary linkages, and double-check all connections before starting the engine.

The fuel pump inertia shut-off reset switch on a 1991 Oldsmobile Cruiser is typically located in the trunk area, often near the rear passenger side. It may also be found under the dashboard, close to the driver's side. This switch is designed to reset the fuel pump after a collision or sudden impact. Always consult the vehicle's manual for precise location and instructions.

To replace the battery in a 1994 Oldsmobile Cutlass, first, ensure the vehicle is turned off and the keys are removed. Open the hood and locate the battery; disconnect the negative terminal first (usually marked with a minus sign) to prevent any electrical shorts, followed by the positive terminal. Remove any securing bracket or strap and carefully lift out the old battery. Place the new battery in the same position, reconnect the positive terminal first, then the negative terminal, and secure it with the bracket.

It more than likely is the heat shield on top of the converter. It probably has broken loose.

It's a bit tricky actually. I bought a Haynes manual, and the diagram within does not display this particular motor and so is pretty useless. The thermostat housing is located on the end of the top water hose mounted sideways on the top of the engine underneath the throttle body and right next to the junction of the exhast manifold and header. You will have to remove the air cleaner box for sure, but access is extremely restricted compared to the 3.1l.

To remove the windshield fluid tank on an Oldsmobile Cutlass for battery access, first disconnect the negative battery cable for safety. Next, locate and remove the screws or bolts securing the fluid tank to the vehicle, typically found near the top or bottom of the tank. Detach the fluid hose from the pump, ensuring any remaining fluid is drained, and then carefully lift the tank out of its mounting position to access the battery.

It is behind the ashtray, You may have to remove the ashtray mount to see it on the left in a half moon metal holder. KEZZART:

remove the entire ashtray assembly by removing the 4 easy to see hex screws, 2 at the bottom corners and two you can see at the top corners when the ash tray is opened - the cig lighter will still be attached by wires so be careful not to pull out the ash tray too hard or too far - the flasher is inside the ashtray hole to the left and may be held in place by a small clip which often comes loose so it may just be laying loose at the end of a long wire - the flasher is a squat little silver cylinder that just unplugs - remove the clip if it is still attached to the flasher and put it on the new flasher and plug in - then clip it all back in place though i just lay it loose and dont bother clipping it - i sure wonder what jerk designed it to be so hard to find and replace