Furnaces

The furnace, whose name is derived from the Latin word fornax, which means oven, is a heating device utilized for both home and industrial purposes. Questions about furnaces can be asked and answered here.
Usually the filter is right on the inside of where the return airduct meets with the furnace. You usually have to take off the sideor front panels of the furnace to gain access to where the filteris. Usually these involve sliding them up and out but it can vary.Check an online owners manual for the...
HVAC Service Technician
Contact the manufacturer of the unit. Give them the model andserial number. See if they can send you one via email or mail.
Yes, however, wood can be carbon neutral. The process of burning wood also does not emit any additionalcarbon dioxide than the natural biodegradation of the wood if itwere left to rot on the forest floor. Over the course of a tree'slife it absorbs carbon dioxide from the atmosphere and thenreleases...
Heat load calculations need to be conducted for home to determinethe proper size furnace. There is no simple answer to thisquestion. There are a number of factors that can effect what sizeyour furnace should be. Example: square footage, duct work size,insulation factors, windows etc. I recommend...
A blast furnace used in steelmaking is about 130 ft or 40 metres.
Cost depends on where the furnace is to be relocated. Duct worktransitions may need to be made, electrical and gas lines may alsoneed to be ran. Contact a reputable HVAC contractor to give you anestimate.
It depends on the efficiency you are looking for and the metal workthat needs to be done. Contact heating and cooling companies to getestimates.
yes u can if u are good with duct work put a down draft furnace in a basement and pipe it up one floor well not recommended it will work i did this to help a lady get threw winter who had low funds and it has worked quite well u need to build a custom box for the furnace to sit on to make this work...
Cost of a furnace depends on the efficiency, the brand unit,transitions needed to be made, and the cost of a qualityinstallation. I recommend getting estimates from qualified andreputable HVAC companies.
Mainly the type of coke being used. The sulfur, ash and carbon content are different.
A standard 1" non-pleated furnace needs to be changed once every 30days.
There is the possibility it is oversized causing it to heat the house, shut off and restart otherwise known as short cycling. Ideally the furnace would be sized to heat the house at the same rate the house loses heat on a design day.
The temperature should be set according to your comfort preferences. The temperature at which most people feel comfortable is in the range of 68°F to 72°F. Setting the furnace temperature higher will result in increased operating cost, as heat is lost through air leaks and radiation,...
Defective thermocouple or possibly a dirty or clogged pilot orifice.
Yes you can get a high wind cap for the vent.
When your air conditioner runs during the summer, air blows over the extremely cold cooling coil, through the filters and into your house. When the air moves over the coil, it deposits most of its heat into the coil, meaning that it's cooled down when it moves into your house. If you have a...
No, furnaces are forced air heat. Boilers are hot water heat.
Answer . Check the heater control valve. If it's stuck slightly open, the heater may be fighting against your AC system. BTW, that's the most common reason for the condition you describe.
Tax laws change every year. Check with your accountant.
Hi, The wiring diagram is no problem but you didn't say what typeunit or model number? Are we talking heat pump, split system,package system, strip heat and etc. Goodman is as good a unit asanybodys in my humble opinion. They are also very bargain pricedwith easy service features and readily...
The right gas pressure for a gas furnace to operate well is between12 to 13 WC. However, it can still operate as low as 10 WC.
The actual time may vary according to the traffic and weather. Theapproximate driving time between these two places is 6 hours 30minutes.
They were manufactured by J. A. Topf und Soehne, Erfurt (Thuringia). The firm had a reputation already before World War 2 for making highly efficient crematoria that used very cheap fuel (lignite or 'brown coal').
Preheated blast air blown into the furnace reacts with the carbon in the form of coke to produce carbon monoxide and heat. The carbon monoxide then reacts with the iron oxide to produce molten iron and carbon dioxide. Hot carbon dioxide, unreacted carbon monoxide, and nitrogen from the air pass up...
The gas furnace pilot (flame is lit all the time) is sometimes referred to as a pilot light, but no matter what you call it, its purpose is to serve as a small ignition flame for the gas burner. And when this little flame fails to operate properly or go out, it's one of the most common reasons a...
Meshak, Shadrak and Abednigo. They refused to bow down and worship King Nebukanezzer so he had them thrown into the furnance.
yes it certainly can. Gas furnaces usually have a Fan/Limit combo switch. It has a helix coil that heats up and triggers the fan to start when it reaches operating temperature. When it gets too hot, it breaks the low voltage to the gas valve and shuts off the burners. As it cools off, the helix...
Your thermostat might be shorted out. Remove one of the wires off of the stat to see if the furnace will shut down that way.
1. By increasing size and improving design. 2. By injecting hydrocarbons (the C in these means less coke is needed so there's more space in the shaft for the ore) 3. Enriching the blast air with pure O2 (this increases the flame temperature where the air gets heated and it increases the production...
An oven heats objects inside of a chamber, a furnace heats the air around it.
The first thought is to use your whole hose recirculating fan on your your return air duct. What type of furnace or stove is this?. >>>>>>>>>>>>>>>>. If you smell exhaust in your home you could be leaking carbon monoxide into it as well. Get it checked out NOW...
Most standard settings vary between 95psi to 140psi. This depends on what tip size @ angle is being used. Please note that tip size/angle is NOT the only deciding factor!
when the wall thermostat closes a contact (at the set temperature), 24 volts is passed through a concave metal disk in the sequencer. The current heats the disk expanding the metal till it pops to a convex position pushing a plastic insulator rod, attached to a metal bar that closes the 208v or 240v...
Mark Gibbles, is fully entitled to sueing hamsters for nicking his name AKA GIBBLES. He chucks them in furnaces, however he fries their innards and then eats them for snacks and uses their fur for clothing and hair.
i have a model 125u19 payne furnace i move the thermostat but nothing comes on in the furnace and the pilot light is lit
How to clean a condensate line . Use compressed air.
Unless you want the power off or there is an overload condition that caused the breaker to trip.
James Beaumont Neilson
Slag is the waste which is skimmed off the top of the molten iron that comes out of the blast furnace. It is a mixture of calcium and magnesium compounds, plus other impurities such as iron oxide, but is mainly calcium silicate. The formula for calcium silicate is CaSiO 3 .
If you have hot water heat or steam heat, it will still work. Gas or electric heat has nothing to do with the water system.
Induction furnace and transformers has the same principle. A high-frequency current is passed via water-cooled coil acting as primary coil of the transformer. AC current is passed through the primary coil leading to the generation of magnetic flux cutting the secondary coil. Electromagnetic...
because it blows hot air in it.
the hottest part of a blast furnace are the blue flames which has fully reacted with O2. the yellowish part contains carbon as it's not totally reacted.
Out of fuel oil, or gas shut off
Answer . \nCall a plumber.. Answer . Check that you re-opened all the valves you closed.
Italian glass blowing techniques such as latticinio and zanfirico are adapted here to make beads. Furnace glass uses large decorated canes built up out of smaller canes, encased in clear glass and then extruded to form the beads with linear and twisting stripe patterns. No air is blown into the...
A furnace can be heated by fossil fuels like coal, coke, or naturalgas, which is chemical energy or it can be electric.
the metals extracted by a reduction blast furnace is : iron and steel these two are the right answers
Elkanah Ingalls; he was a blacksmith and for many years head of the R.I. Mechanical Association. He and his wife were burned to death in their home at Providence, R.I. in Dec. 1877.
it heats your house
Furnace is an enclosed fire place show me parts of a coal fired furnace
Cause it's cold n1gga!
A redundant gas valve has two or three valve operators physically in series but wired in parallel with one another. This built in saftey feature allows any operator (pilot or main) to block gas from getting to the main burner. EX: standing pilot, intermittent pilot, and direct burner are classified...
A structure or apparatus in which heat is generated, as for heating houses.
The excessive heat will implode the ball due to internalized pressure being exerted inside and outside of the ball.
I was quoted $185. Charlotte, NC.
a brick mason can repair your chimney,but not all brick Masons have exp. repairing chimneys
simply by measuring the coil voltage, coil current & power factor.
If you're referring to cremation, the apparatus is called a Retort.
It is called a cremation retort.
tell me funtion of tube types of furnace
You have a problem in the regulator, or you need a new 'thermocouple' . Both simple work for a competent gas fitter - I'd recommend calling one.
Electrodes are Submerged in the Submerged Arc Furnace, into the raw materials. Reason, for allowing the electrodes to reside inside the charge mix, is the high resistance of the ores. Three purposes are served : 1. The heat coming out from arcing is utilized for preheating the ore at the upper...
Yes & there are companies that test for it now.
Formula : F = (C x 1.8) + 32 . F = ( 118 x 1.8) + 32 . F = 212.4 + 32 . Fahrenheit = 244.4°
it is as like as viscous liquid so the angle of repose for it under 30 deg
Indtherm is one of the leading manufacturers of Induction Furnace, based in Kolkata (India).
In steelmaking, it is a vertical cylindrical furnace used for melting iron either for casting or for charging in other furnaces.. René-Antoine Ferchault de Réaumur built the first cupola furnace on record, in France, about 1720. Cupola melting is still recognized as the most economical...
In dc eaf 50% less electrode consumption & 5% less in power consumption and also uniform melting are advantages
There is a small nipple located on the bottom of the burner itself. This nipple has a hex edge to it so you can use a small wrench (I think its a 1/4 inch) to open it. Turn it counterclockwise a few turns, then turn the thermostat up till the burner turns on. Make sure you have a bucket to catch the...
In a furnace large amount of the heat supplied is wasted in the form of exhaust or flue gases.. that s called as heat loss in a furnace..
You might just need to replace the radiator hose or your radiator is cracked.