answersLogoWhite

0


Best Answer
Copy

What kind of car??

1999 grand am

User Avatar

Wiki User

โˆ™ 2015-07-15 19:05:30
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you get the instrument cluster bezel off to replace the plexiglass cluster cover?
Write your answer...
Submit

Related Questions

How do you remove the instrument cluster in a 1997 Nissan Maxima GLE?

* Disable the airbag system * Remove the instrument cluster bezel * Remove the retaining screws and pull the cluster forward * Unplug the electrical connectors and remove the cluster from the car


How do you remove the instrument cluster on a 2002 explorer?

Disconnect negative battery cableTilt the steering wheel to its lowest position and remove the instrument cluster bezelRemove the instrument cluster retaining screwsPull the instrument cluster out,unplug the electrical connectors from the backside and the shift indicator from the bottom (automatic trans models) then remove the cluster from the instrument panel


How hard is it to replace instrument panel lights on 1995 Nissan Quest?

# Disconnect the negative battery cable. # Apply the parking brake and block the rear wheels. # Turn the ignition switch to the OFF position. # Shift the gearshift lever to the 1position. # Position the steering wheel in the full-down position. # Remove the two instrument cluster bezel screws. # Separate the instrument cluster bezel from the instrument panel enough to gain access to the electrical connectors. Disconnect the following electrical connectors: # Rear window wiper/washer switch # Rear window defogger switch # Hazard warning flasher switch # Power E-AT switch, if equipped # Security indicator lamp, if equipped # Cruise control ON/OFF switch # Headlamp switch # Remove the instrument cluster bezel with the switches attached. # Remove the four instrument cluster screws and separate the instrument cluster from the instrument panel. # Position the cluster to gain access to the gearshift indicator. Remove the gearshift indicator from the cluster. # Disconnect the electrical connectors from the instrument cluster and remove the cluster. # The installation is the reverse of removal.


How do you replace instrument panel bulbs in a 98 Toyota Corolla?

Remove the 2 screws at the top of the instrument cluster bezel (or dress front cover), carefully pry out with a small screwdriver and set aside. Remove the 4 screws that hold the instrument cluster to the inner dash and pull out. Turn instrument cluster over to access the bulbs for removal and replacement. Twist the bulb retainer to remove.


How do you change the in dash heater control on a 1998 Chevy blazer?

Remove the two screws at the top of the instrument cluster. This will allow you to pull out the entire bezel. Pull out the bezel, and pop the switch out from the bezel.


How do you replace the radio in a 98 Chrysler cirrus?

Remove the instrument bezel.


How do you remove the stereo on a 1995 Dodge Caravan?

You have to remove the vent & bezel assembly from below the radio first, then the entire dash bezel from around the instrument cluster & radio.


How do you replace the instrument cluster bezel on a 2001 Dodge Ram 1500 pickup truck?

The Bezel can be removed by simply pulling it away from the dash. It is held in place by 13 tension fasteners. Place the tilt wheel in the lowest position and place the shifter in low so the bezel will clear them on removal. Use caution if the bezel is cracked as it may break completely when it is pulled off.


How do you remove the instrument cluster bezel on a 2000 ram 1500 sport?

Nevermind. I found the solution through another question.


How do you remove the dash speakers in a 1996-2000 dodge caravan?

You have to remove the vent & bezel assembly from below the radio first, then the entire dash bezel from around the instrument cluster & radio.


How to replace heater core 1999 ford ranger?

1) Disconnect battery terminals to disable air bags. 2) remove radio bezel 3) remove instrument cluster bezel 4) remove kick plates 5) unbolt instrument cluster pull forward 6) push in flat on speedometer cable to disconnect remove cluster 7) disconnect heater hoses in engine compartment at passenger firewall 8) drop heater plenum box 9) separate heater core from box


Bezel insrtument bezel?

can u describe what is the car instrument bezel ,and how its maufactured?


How do you take out an instrument cluster in a 1996 Chrysler sebring jxi?

Pop out the bezel around the radio and note the 5/16 bolts (4 of 'em ) holding the main cluster bezel down. Remove the Fuse Access door on the driver side with the door open and remove the 5/16 screw just inside the access area. Remove them and GENTLY pull up on the assembly until it begins to pop out. The entire assembly should lift out from around the instrument cluster. Remove the 4 screws on the cluster (same size as the others) and lift the cluster. Lay the cluster down upside down and CAREFULLY unplug the cluster. One Blue, One Black connector. VIOLA! it's out. Replace in the reverse order.


How do you remove the instrument cluster from your Plymouth breeze?

1. disconnect negative battery cable and wait 2 minutes (this disarms the airbag circuit while you work in that area). Remove the left end cover by pulling outward. Tilt steering column down to lowest position. remove instrument cluster center bezel (around radio and environmental controls) by disengaging 4 clips (2 on top and one on each side). 2. Remove 4 instrument cluster hood mounting screws. Three screws are located behind the center bezel and one screw is located at the left end of the hood. Pull on hood to disengage hood and remove instrument cluster hood. Pull instrument cluster rearward to disengage 8 clips and disconnect wiring connectors from panel. Remove instrument cluster.


How do you replace the heater switch in a 2002 s10 truck?

Pull the front dash bezel out that surrounds the cluster and the radio and the a/c-heater controls out and then remove the controller and replace the switch.............


How do you replace gage lights 94 dodge ram van?

Remove the instrument cluster (hidden screws on bottom of bezel, by door, and under glove compartment door) Remove the entire white plastic assembly (careful, there's a linkage back there for the PRND21 visual). Unscrew and replace the bulbs.


How do you take apart the dashboard on a 1999 Mitsubishi galant?

If youre referring to the dashboard cluster, theres two screws in the top of the cowl housing on top, remove the bezel and remove the 4 screws holding in the instrument cluster.


How do you replace the dashboard lights on 1997 F-150?

To replace the dashboard lights on the 1997 F-150, you will first need to remove the dash bezel and dash cover in order to access the lights. Then, remove the instrument panel cover below the bezel and remove the burned out lights. Replace the lights and add the cover, dash cover, and bezel back to the dashboard.


How do I Change the instrument cluster 2001 Volkswagen Beetle?

gently pop off the outer bezel with a flat head screwdriver. be careful not to break bezel. should come off fairly easy. there you will find two star head screws. take those out. this should free up the cluster. at this point your work area becomes very small. there are two connections on the back of the cluster. pry the release up and disconnect the cluster . install the replacement cluster the same way the old came out.


Removing instrument cluster on 2008 F350?

take off center finish panel pop out your cigaret lighter bezel and the bottom right bezel should be i-pod or blank bezel even a dual fuel bezel. take out the 2 7mm screws located inside when u pop of the bezels.gently pull panel off.have some one hold this out of your way.try not 2 scratch anything.on your cluster finish panel you have two 7mm screws on the bottom and two on the top.if you have tilt ,tilt it all the way down.you need to have your shift lever all the way down.you need to unplug any bezels that are on your cluster panel.once that's off two 7mm screws hold your cluster in .pull on cluster from bottom then tilt out.


How would you replace the instrument panel light bulbs on a 1998 Chevrolet prism?

Look up at the upper part of the instrument panel and you will see (2) recessed Phillips head screws. After removing these screws you should be able to pull down on the bezel and carefully snap out the bezel. It is tricky, so be carefull. It helps if the tilt steering wheel is all the way down.After the bezel is removed you will see the instrument panel is being held in place by screws around the outer edges. after removing these screws the whole instrument cluster comes out with the cables still attached. You will see the bulbs that are twist locked into the circuit board. It is then easy to untwist and remove them.Rick Kellerrickadak@comcast.netAnswerThe previous answer sounds correct, but I was able to replace an instrument light by reaching up behind the panel. It's a little crowded, but not too hard to access.


How do you change the light bulbs that illuminate the dash on a Mazda Protege 5?

Remove 2 screws above the black trim bezel surrounding the Instrument cluster. Insert a hard plastic or nylon prying tool into the crevice surrounding the trim and gently pry evenly all around the bezel until it pops off, or use a hook tool to grasp and pull the black bezel off. Now you will have to remove 4 screws that hold the instrument cluster in place. Gently pull cluster forward and tilt down to expose electrical connectors. Carefully remove connectors by pushing in on the release tab and pulling up on the wires, this will remove the connector, repeat this procedure for the remaining connectors. Lower the steering column and gently remove the instrument cluster. You will notice little lamp holders at the backside of the cluster, genly grasp the holder(s), turn and pull up using a plier. Make a note where each lamp was removed. Purchase replacement part at your favorite Mazda dealer. Now just put everything back together and reinstall the instrument cluster.


How do you get hazard button out of dash?

its recalled u can take it the dealer and they will do it You remove the bezel surrounding the instrument cluster panel, should be only 2 small screws. Once you do that you can squeeze your hand in and get it free.


How do you fix a 1996 Grand Cherokee limited instrument cluster?

Removing he instrument cluster from a 1996 Grand Cherokee Laredo Ltd. is easier than I thought it would be since Jeep designed it to be removed from the front of the dash. You don't have to lie upside down on the floor to do the work. You start by first removing the 6 visible screws surrounding the top underside of the bezel. Then you carefully pry off the two wood-grained trim pieces surrounding the controls below the instrument cluster bevel to the left and right of the steering wheel column. That exposes 8 more screws you must remove. Once these screws are removed, you carefully pry down the top of the bezel that surrounds the instrument cluster, pulling it forward at the same time. The bezel should pull forward and it can now be removed, exposing the instrument cluster. The instrument cluster is held in place with four screws. Use a magnetic tipped screwdriver, so you don't lose them inside the dash. The cluster may now be removed. The good news is that it is simply plugged into a socket behind the cluster, there are no wires to disconnect, which is nice. You gently rock it back and forth, while pulling it towards you. At this point you can either replace the entire cluster, which my local Jeep dealer charges about $325 for, or you can further disassemble the cluster to replace individual gauges, which I am doing. My speedometer stopped working and the dealer charged $118 for its replacement. You must supply your VIN and odometer reading and the old speedometer, to avoid the core charge. Take it slow on removing all plastic parts, to avoid breakage and you should do all right. If you need further help, give me a call at 650-638-5905 and I will try to help as best I can. I hope this helps give people the confidence to do this simple task by themselves.


You have a Toyota Corolla 2002 recently the light on the dashboard has gone out on half of the screen blacking out the heat index and part of the fuel level is there any way you can fix this problem?

remove the 2 Philips screw holding the black bezel in place (in top of it), remove the bezel, remove the 3 Philips screw holding the cluster in place, take the cluster aka the thing with all the gauges in it . get the cluster out, you will see three green light sockets that are screwed into the back of the cluster, they are holding 194 type bulb, remove them, and replace the bulbs. might as well replace all 3 of them. make sure to reinstall the little plastic cover over the new bulbs. put cluster back in place, screw 3 philipps, reinstall bezel, reinstall the 2 screws.