0
Chevy Camaro
This category covers general questions about the Chevrolet Camaro, a pony car manufactured by General Motors and sold through its Chevrolet division. The Camaro was designed to compete with the Ford Mustang. Production of the model began in 1966.
4,208 Questions
Will a air conpressor on a 98 Camaro v6 fit on a 93 Camaro z28?
dont think so it should be a different bolt pattern if needed just cross reference part number on autozone.com to see if there the same
Your 1996 Camaro has an intermittent problem of the low trac light coming on just as you stopping?
Try bleeding the brake system including the ABS pump.
What exhaust system makes a camaro with a 3.8 v6 sound like a v8?
One with a V8 bolted to the front of it !
What's the idle speed during timing and timing for a 1970 318 2 Barrel?
usually about 750 rpms for automatic trans and 650 rpm with a manual trans.and don't forget to disconnect and plug vacuum hose that goes to distributor advanceand timing for Chrysler runs normally about 16 degrees Before tdc.check under hood to see if it is listed on a sticker..
I have a 2004 Chevy Blazer that I believe had the same issue as you. The wiper arm has a plastic covering over it. You will need to remove it. I using a a Flat head screw driver pry it off where the wiper arm bends. This will allow the base of the plastic piece to pop off the rear of the wiper arm. You can now take a 1/2" socket and tighten up the nut that is under that plastic covering. That was the solution for me anyhow. My driver side wiper arm wasn't moving at all, but the passenger side was. Hopefully that works for you.
What is the switch marked SGS for on your 1997 3800 camaro?
The switched labeled SGS stands for "Second Gear Start". This allows you to start off in second gear when accellerating.
How do you install a window motor for a 1995 camaro?
Place the regulator in position and engage to the guide channel.Secure the regulator to the door (you may have to plug it in and lower the window the slightest bit to get it to line up)with rivets and a rivet tool.(you can use small screws but they can work their way loose so I don't recommend it) If the regulator won't line up, use the switch and let the window down slightly. Plug in electrical connector if you didn't already. Tighten all the channel nuts nd reinstall the door panel.
What Transmission dose a 1984 Camaro have?
It's most likely got a 700R4. One way to find out would be to check into getting a transmission pan gasket, and the parts store will want to know how many bolts are in the pan and what the pan is shaped like. Then, you will know which tranny is in there.
What Transmission came in 85 5.0L Camaro Coupe?
It could have either a 4-speed automatic or a 5-speed manual tranny
What six speed transmission is in a 1998 camaro Z28?
The Z28s have a T-56 six speed from the factory both 5th and 6th gears are overdrives, thus the excellent highway mileage.
How do you adjust idle speed on 92 camaro?
It's done by sensors, if the idle is off you need to replace either the IAC sensor or the TPS sensor.
Throttle Position Switch (TPS)Tools needed:- Digital Volt-Ohm-Meter (VOM)
- Jumper Wires (make your own)
- Auto Xray Scanner (if available) will eliminate the need for VOM and jumper wires.
Turn on ignition, but don't start the engine.
With a scanner: plug in the scanner and read the TPS voltage. It should be 0.54Volts +/- 0.075Volts
With VOM and jumper wires: disconnect the connector from the TPS. Using your jumper wires, make a connection allowing some room for the VOM terminals to contact the jumper leads and read the TPS voltage.
If out of spec, loosen the two screws holding the TPS to the throttle body, and slightly rotate the TPS up or down, reading the voltage until it comes into specification. Tighten screws. Using the throttle lever, rotate the throttle to WOT (wide open throttle). The TPS voltage should be over 4.0 volts. Close the throttle again, and then slowly open it to WOT, observing the voltage reading. It should increase progressively and in a linear fashion. If it sticks or jumps or falls off at all while doing this check, that could mean a bad TPS switch and could be a cause of stumbling and driveability problems.
After setting the correct voltage, turn off ignition switch. Remove jumpers/scanner and reconnect the TPS connector as required.
When you drive over a clicking bettle.
What are the specs of a 1994 z28 Camaro?
Source: theautochannel.com
SPECIFICATIONS:
1994 CHEVROLET CAMARO Z28
Base Price $ 16,779
Price As Tested $ 19,164
Engine Type V-8, ohv - pushrod - 16v, smpfi
Engine Size 5.7 liter/350 cid
Horsepower 275 @ 5000
Torque (ft/lbs) 325 @ 2000
Wheelbase/Length 101"/193"
Transmission six-speed manual w/od
Curb Weight 3440
Pounds per Horsepower 12
Fuel Capacity 15
Fuel Requirement Unleaded premium (91 oct)
Tires Goodyear Eagle GA P235/55R16 M+S
Brakes anti-lock standard disc/disc
Drive Train front engine/rear drive
PERFORMANCE
EPA Economy - miles per gallon,
city/highway/observed 17/25/20.1
0 to 60 mph 6.5 sec
1/4 mi (E.T.) 14.9 sec
Coefficient of Drag (Cd) .34
How do you replace the front turn signal bulb located on a 1999 Chevy Camaro?
Take the light assy off and it screws in from te rear.
To expand on the cryptic and nearly useless advice above, try this. Remove the ONE 10mm bolt at the top rear center of the headlight assembly. DO NOT remove any of the metal bracket bolts or change any of the headlight adjusting screws. Slide entire headlight assembly towards the centerline of the car until the two positioning tabs at the bottom of the assembly line up with the slots in the headlight bracket. Pull the entire headlight assembly forward and angle the assembly to clear the fender at the outer edge. At this point, you can use a screw driver to release the wire sockets for high and low beams and completely remove the headlight assembly (easier access to the turn signal bulb) or just leave the wires connected and work around them (harder access to the turn signal bulb, but possible). The turn signal bulb socket is now accessable. Press in the locking tab and rotate the socket to remove it. Replace the bulb with a 3157LL bulb. (The factory bulb is a 3157K, the 3157LL is a "Long-Life" bulb, and considering what a pain it is to change, long-life is well worth the extra buck.
1. Jack up car and support on jack stands (or use ramps)
2. Remove three screws securing under-cover to air dam.
3. Grip the light bulb socket and twist while compressing the locking clip.
4. Pull bulb straight up out of the socket and replace.
I've just done our 2002 Camaro front left turn bulb after discovering this answer here - but it's even easier than the above I think...
The piece of plastic that fills in under the front of the car is held to the front fender, the wheel well liner and the air dam with a number of screws. There are also two splits in this cover immediately adjacent to 2 of these screws - if you remove just the two screws that are behind the air dam that connect the black plastic to the finder, you'll find that you now have a small door that will hinge downwards to let you get your arm in.
Of course I discovered this after I'd removed the whole thing.
I think with some cars, you have to enter in from the hood and go behind where the headlights are. Not sure if this helps, but it's worth a shot.
Where is oil sending unit on 95 z28 camaro?
Oil level sending unit is located in the side of the oil pan.
Oil pressure sending unit is located in 95 at the back of the intake really not fun to take off while engine is in car but possible just feel back there with your hand and you will find it. 93 had them above the oil filter.
it was created because they needed a car to take people from place to place..:) so not true im just guessing
What causes a engine to shut off while driving and will not start back up in a 1994 Acura Integra?
ignition control module also called the ignitor No it is not the ignitor. An ignitor helps start the car however it does not keep the car running.
Where is the horn relay located on a 1989 Chevrolet Camaro?
It is on the passenger side at the firewall behind a cover.
