Where is the water pump on a 2000 Chrysler Sebring convertible limited?
It is inside the passenger side of the engine, driven by the timing belt.
Where is crank sensor located on 97 sebring lxi?
where is the crank sensor located on my 1997 Chrysler sebring lxi
How do you remove the rear seat in a 1996 sebring convertible?
It seems that you just need to PULL UP VERY HARD! I'm in the process of doing my seats, now. I tried the "push back & lift up" method, to no avail. I didn't break the plastic tabs, either. Try doing this with the top down; it makes it easier.
There are two metal "loops" on each side that would be positioned about the middle of each seating position where the seat meets the carpet. I'd recommend prying up on each side of these with two very large screwdrivers, as there is no support in the middle of the loop and you will definitely tear your seats up this way. Once you get it unlocked you should then put something over the slot to prevent them from reingaging the plastic lock tabs. Try not to pull from the middle of the seat as you will bend the metal reinforcement that keeps the seat snug to the body of the car.
You can also do as the previous poster said.. putting the top down and pulling with all your might. I can confirm that the push back & lift up method will not work in this situation.
Have a 1997 Chrysler sebring the compass just says ccd what does this mean and how can it be fixed?
This means that the compass is in the calibration mode. If you have a Chrysler Sebring owners manual, it will help you finish the calibration for the area you live in. When you look it up, go to the "Index" section of the manual and you will find it. If I remembered or have my manual on me as I type this, I would just write what to do. Just read through it and you will find the section to get you back to "normal" operation. Take care and good luck :)
Where is the thermostat on a 2006 Chrysler Sebring convertible 2.7 liter?
It is under the housing where the lower radiator hose attaches to the engine.
Where is the thermostat on a 1997 Chrysler Sebring convertible 2.5L?
On a Chrysler Sebring 2.5L the thermostat is under the housing where the lower radiator hose hooks to the engine.
Where is a ignition coil located in a 1999 Chrysler Sebring?
there isn't a traditional ignition coil on this vehicle, it is part of the distributor cap, and cannot be replaced as a separate part. on my 97 sebring 2.5L it cost around 350 dollars for the cap and coil a few years ago.
Where is the camshaft position sensor located on a 1998 Chrysler sebring 2.5l?
it is an part of the distributor unit. you have to change out the entire distributor.
How to replace push rods on a 2002 Chrysler sebring gtc?
A 2002 Chrysler Sebring has an overhead cam engine. That means it does not have push rods.
Where is the drive belt on a Chrysler Sebring?
The Chrysler Sebring drive belt can be found on the front of the engine. It is also referred to as a serpentine belt. The timing belt can be found behind the front engine cover.
What is the part number for a 2000 Chrysler Sebring daytime running lights relay?
The part number for a 2000 Chrysler daytime running lights relay will be different for each manufacturer. Standard Motor Products sells this part as number RY-254.
How do you remove the front brake rotors on a 2002 Chrysler sebring coupe?
Should be the "peel off" type Remove wheel Remove caliper mounting bolts Slide caliper off rotor Rotor should slide off hub assembly
How do you reset the tire pressure monitoring system on a 2007 Chrysler Sebring?
Fill the tires up with air they will reset after that
Where is the obd plug located on a 2001 Chrysler Sebring sedan?
The plug is under the dash on the driver side. It is a rectangular plug.
Why 2001 Chrysler sebring dies at stop stop signs?
Could be the "Torque Converter Lock-up" Solenoid sticking in the lock position.
Why does your Chrysler Sebring overheat when you turn on the air conditioning?
It puts additional strain on the engine, so a little warmer than normal temp is ok, but im guessing that one or both of your cooling fans are not running up to speed. see the evaporator coil sits in front of your radiator, and the heat from that gets transfered to the radiator causing it to run a little hotter. Usually there is a fan that blows additional air over that coil, and if it is not running at top speed, it will cause the heat to make the radiator run much hotter. I would see about replacing that fan.
How many mpg can you get Chrysler Sebring?
I have a 2005 Sebring which now has 65000 km. I purchased this car new. I consistently get 600 to 640 km per tank of fuel with the average fill up of 51 to 55 liters. My fuel minder states 8.1 to 8.2 liters per one hundred kilometers and if I do the math I find the fuel minder to be very accurate. I am very satisfied with this Chrysler Sebring and it has also been better on gas compared to the Honda I had before this, not to mention I like this car better then the Honda believe it or not.
Why won't my 2005 Chrysler Sebring windows roll down?
i will bet its BROKEN WIRES if it's not the fuse The most likey place is where the wires run from the body (driver side) into the door. the rubber boot hides the wires. The wires get brittle and break from the door opening and closing. Splice a 3" wire on ech broken wire with crip connectors. then loop the splice (this loop prevents future breaking). reattach each broken wire after you loop each spliced wire. i HAD ABOUT 8 WIRES ON MINE BREAK. Time consuming, but it works great.
How do you disarm a factory alarm on a 1996 Plymouth voyager if the remote is broke?
Try unlocking all doors with the key. There should be switches on the backs of the key cylinders on the front doors and liftgate.
How do you adjust the headlights on a 1999 Chrysler Sebring?
pop the hood. above the headlights there is a "hole" more toward the fender with a plastic gear looking thing it turns to adjust the lamps. this is on a 97 but up to 2002 is pretty much the same.
Where is the map sensor located on 2005 Chrysler sebring?
Passenger side near the water inlet (has three wires coming out). It's attached by one phillips head screw located underneath the sensor. Use a stubby screwdriver if you have one.