0
Chrysler Sebring
The Chrysler Sebring is a range of middle-sized cars manufactured by American carmaker Chrysler between 1995 and 2010. It is one of the few practically priced automobiles available in sedan and convertible body styles.
2,284 Questions
In a 2003 Chrysler sebring What is the difference in engines between a convertible and sedan?
The convertible and four door sedan use the same engines.
How do you change the battery in a 1996 Chrysler Sebring Convertible?
You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
NewIt's located in the front wheel well. Remove front left wheel, then unscrew battery door.Actually, there's no reason to remove the driver's side front wheel, just turn wheel to left and right behind the wheel you'll find an access panel, remove this and there's your battery. Recommend removing negative post first to prevent "short circuit" when removing positive terminal. Good Luck!
How do you set the clock on a factory Chrysler sebring stereo 2005?
Turn the key to accy' and turn the radio on. Push DISPLAY button until the clock time shows on the radio display. Look to the top right of the radio and you will see 2 small holes there that are marked "H" and "M". Using a paper clip or tip of a ball point pen, push the "H" button until the desired hour is reached, repeat doing the same for "M" for the minutes. You will notice there are no separate AM or PM settings for the clock.
How do you stop the weather stripping from squeaking when the Sebring convertible top is down?
Just spray it with Teflon or better yet silicone spray- mine was squeaking something terrible -- a few sprays at the joints and the stripping edge did the trick. Hope this helps
If you are installing the timing chain on a 2.7L, the number one cylinder will not be at TDC. That is normal.
If you are installing the timing chain on a 2.7L, the number one cylinder will not be at TDC. That is normal.
Where is the fuel shut off of a 2002 Chrysler sebring and how do you reset?
Chrysler doesn't use shut off switches. The fuel system is computer controlled with relays.
How do you replace a brake light bulb on a 2008 Chrysler Sebring?
I have a 2007 Chrysler Sebring. There are two black wing nuts in the trunk ( refer to owners manual if you cant locate them) twist them off. there is also a white clip that is holding a small post. after unloosing the wing nuts I placed a small screw driver (flat) between the post and the white retainer clip the whole assembly pops off. twist the housing that is holding the bulb and replace the bulb. in my manual its pg 325
"2. Remove the two plastic wing nuts from the tail lamp
housing. (before I did step three I used the small flat screw driver to release the post from the white retainer clip)
3. Grasp the tail lamp and pull firmly outward pushing
gently on the studs from inside to disengage the lamp
housing.
4. Twist and remove socket from lamp.
5. Remove bulb from socket and replace" Taken from the 2007 Chrysler Sebring owners manual
How do you remove the center console from a 2007 Chrysler Sebring?
The center counsel on a 2007 Chrysler Sebring can be removed by loosening the bolts on the bottom of the Council. The bolts are located at the back of the Council.
Where is the radiator drain plug located on a Chrysler sebring 2002 lx v6 2.7 liter?
It is located on the lower right hand corner on the inside toward the engine. It is very hard to see and best seen from the bottom side.
What is ccd on a 1997 Chrysler Sebring?
It is the communication system between the computers on the vehicle.
Why would the digital odometer and RPM meter work intermittently in a 1997 Sebring JX Convertible?
The problem is in the instrument cluster. It needs to be checked out.
This is a very common problem with these cars as they age. I have seen a number of them where the odometer was blank and/or working intermittently together with the tachometer. The only reliable solution is to get a new one from a dealer.
not trying to make anybody mad but i have the same problem if you take out the cluster then pull off the cardboard from the back there is a small blue resistor it will have a burnt spot where they are you or some one you know could clean it and re solder the contacts i did it and it worked great now hardly any cost to you i hope this works for you Robert
Honda Man's Answer The AC drain is on the bottom of the evaporator case and goes through the firewall. Sometimes the drain can be cleaned using a metal coat hanger and sticking it into the hole from the engine side of the firewall. If it works a rush of water will flow out. It's possible that the case may need to be removed and cleaned if there are excessive amounts of debris like leaves accumulated inside.
The first thing to check is what is the pressure at idle with the engine warm. You will need to instal a manual gauge. If it is above 15 psi, it is an electrical/sensor issue. If it is below 15, it is an internal engine issue.
You have an aftermarket alarm system. The best bet would be to remove it completely.
How do you replace the alternator in a 2000 Chrysler Sebring convertible?
When replacing the alternator on a 2000 Chrysler Sebring convertible begin by removing the belt. Next, remove the wiring. Lastly, remove the retaining bolts. Reverse the process to install the new alternator.
How to change spark plugs on a 6 cylinder Chrysler Sebring?
Here are the steps for removing and replacing the plugs on cyl 1,3,and 5 of the 2.5L V-6:
Disconnect negative cable from auxiliary jumper terminal (I believe this is the ground wire tied to the strut tower on the driver's (left) side of the car).
Unplug the connectors from the MAP sensor and (just to its front) the intake air temp sensor.
Remove the plenum support bracket bolt located rearward of the MAP sensor
Remove the bolt holding the air inlet resonator (the thing with words "multi-point injection") to the intake plenum.
Loosen throttle body air inlet hose clamp
Release snaps holding air cleaner housing cover housing
Remove air cleaner cover and inlet hoses from the engine
Unplug throttle position sensor and idle air control motor connectors.
Pry retainer tab back on throttle cable and slide cable out of bracket. Remove cable from throttle lever.
Slide Speed control cable out of bracker, if equipped. Remove cable from throttle lever.
Remove EGR tube from intake plenum.
Remove plenum support bracket bolt located rearward of EGR tube
Remove bolts holding upper intake plenum and remove plenum
Always remove the ignition cable by grasping at the spark plug boot turning the boot 1/2 turn and pulling straight back in a steady motion
Prior to removing the spark plug spray compressed air around the spark plug hole and the area around the spark plug
Remove the spark plug using a quality spark plug socket with a rubber foam insert
Inspect spark plug condition.
To avoid cross-threading start the plug into the cylinder head by hand
Tighten the spark plugs to 20 ft-lbs (28 N-m)
Install ignition cables over spark plugs
Install new gasket and position upper intake plenum. Tighten blots to 13 ft-lbs (18 N-m)
Install bolts at plenum support brackets (Same torque as above)
Install EGR tube at plenum. Tighten EGR tube to intake manifold plenum screws to 8 ft-lbs (11 N-m)
Install throttle and speed control (if equipped) cables
Attach electrical connectors to sensors.
Install air inlet tube clamp to to 25+/- 5 inch pounds (3 +/- 1 N-m)
Connect negative terminal to auxiliary jumper terminal.
How do you repair keyless entry circuit board for 99 Chrysler Sebring Convertible?
take it to your near autozone,they started making some aftermarket products,if they don't have one for your vehicle take it to a Chrysler dealership and they will match one up but if they have to reprogram it, it will cost extra along with the keyless entry,sometimes they don't have to reprogram them.
Where is the speed sensor on a 2000 Chrysler Sebring?
The vehicle speed signal comes from the transmission speed sensors on the front of the transmission. The abs sensors are at each wheel bearing.
The vehicle speed signal comes from the transmission speed sensors on the front of the transmission. The abs sensors are at each wheel bearing.
Where is the neutral safety switch on a 2006 Chrysler Sebring?
It is inside the transmission, on the valve body. It is called a range sensor.
It is inside the transmission, on the valve body. It is called a range sensor.
