Civil Engineering

Compressive strength measures the largest compression force the material can withstand before it loses its shape or fails.

For M20 grade concrete mix proportion=1:1.5:3

And dry volume factor is 54 percent.

Hence, we required to find quantities for 1.54 cum concrete.

cement required=(1/5.5) x (1.54)=0.27 cum,

Sand required=(1.5/5.5) x (1.54)=4.2 cum,

Stone chips required=(3/5.5) x (1.54)=0.84 cum.

to help support the building. also to build up the building bigger or taller depending on the size of the beam.

The Aswan high dam is the dam located on the Nile River. It was built to help keep it contained. When it was being built , the dam backed up and created Lake Nasser, located near Cairo, a city in Egypt.

That question can't be answered unless we know what sort of scaffolding and how much of it you want, what city you are in...

7.85 gm/cc

The Battle between Harold Godwinson and Harald Hadrada who joined up with Tostig, Harold own brother.

A clever and creative mechanical engineer is the person behind a great coaster.

Depends on the material the I-beam is made out of. Steel? Is it a wood I-joist? And I-beams come in different "flavors" as regards the geometry and cross section of the web. Variables in a question make for a variable answer.

The basic difference between one way and two way slab is load distribution which is depends on support condition and span lengths.Mainly shorter span is carring larger load than longer span.This load distribution can be calculated considering the deflection at any point is same Shorter and Longer Span.

1. Cantilever bridges
2. Cable stayed bridges
   

Subtract the area of the I.D. of the pipe from the O.D. and multiply the result by the length. (I.D. and O.D. are inside and outside diameter respectively)

BHP = Flow(GPM) X TDH(FT) x SG /3960xEFFICIENCY(%)Example: BHP = (100 GPM) x (95 Ft) x (1.0) / 3960 x .6BHP = 4.0

Youngs modulus (modulus of elasticity) E

Poissons ratio v

Yield strength

Ultimate tensile strength

Density

Cost

Stiffness

Heat expansion co-efficient

Sources: Mechanical engineering masters degree

The Bolman truss bridge is a famous bridge that was built in 1869. It was built to carry the train's on the railroad's main line. Hope this helps;] The Bolman truss bridge is a famous bridge that was built in 1869. It was built to carry the train's on the railroad's main line. Hope this helps;]

The compressive strength of bricks varies depending on the type of bricks and what they are used for. The compressive strength of conventional red bricks is 40 to 65 Kg/cm2. In comparison, flyash bricks have a compressive strength of 70 to 120 Kg/cm2.

2.1 bar = 30.46 psi

The density of Grade 76-10 Bituminous Binder is 1.1 gm/cc at 25 degree centigrade with low linear polyethylene modifier (LLPE) polymer.

Howrah bridge was built to link the two cities of Howrah and Kolkata (Calcutta). Refer to link below for more information.

Both are two different scales of hardness measurement.

The thermal expansion of fibre cement sheet is very small. Over the size of a 2400mm sheet, for a temperature change of 30°C, there would be much less than a millimetre change in the length of the sheet.

The expansion joints required between sheets are necessary to accommodate the movement and expansion of the material to which the sheets are fixed, which is usually much greater than that of the fibre cement sheet. (For example timber, steel, aluminium, and plastics expand more than fibre cement.)

pro: you can get over the bridge,

con: it breaks if your obese

There were 2 towers, and cables would be hanging from the towers. Hangers(or stringers) would be hanging from the cables. The hangers and the towers combined would hold up the deck which at the side, gets connected to the anchor. On top of the anchor is the anchorage, which holds up the cables from the sides.

That is a simple description of a suspension bridge.

The purpose of a rail is to keep someone from falling. You can hold onto the rail while walking up and down the stairs.