Electrical Engineering

Only if we are also in contact, directly or indirectly, with ground.

By ohm's law, current is voltage divided by resistance. Conductance is the inverse of resistance, so current is voltage times conductance. No conductance - no current.

If you assume pressure stays the same (so volume is not limited in any way), you can use the ideal gas law, pV = nRT. I assume an initial condition of ~20C temperature (293K). Also, I assume the temperature you're giving is in degrees F. 35000F = 19427C. If the above assumptions are correct, air will expand 19427 / 293 = 66.3 times its' initial volume.

Yes, but the sensitivity and frequency response will be very poor. The diaphragm on a microphone, corresponding to the voice coil and cone on a speaker, is extraordinarily light and compliant.

To calculate watts you need two of the three: Voltage (V), Current (A) and Resistance (ohm).

Power (Watts) = (V^2) / R = (I^2)R = VI

RS422 and RS485 and the now popular USB

The primary line side of a 3 phase transformer should be marked H1, H2, H3. The line side is the incoming voltage that you want to step up or step down or isolate.

cause if the doctor didnt wear gloves when he was giving you the rubber glove treatment, hed get poo-ey fingernails

To remove melted solder, either as clean-up from a poor solder job, or in preparation for removing a component.

Resistance ideal transformer is the one having no core losses, infinite permeability no mmf needed to set up flux), windings are having no resistances or reactances.

18.5v should be fine for a 15-16v application. remember circuits will only draw the amount of current they need, no more. you could also try adding a current limiting resistor in series with the load. use a VOM for this testing (as the load).

Zero = Nothing = Nil = 0 Hertz or Cycles per Second Direct Current is just as its name says: it does not alternate so it does not have any "frequency".

There are essentially 2 types of connections for a 3 phase AC transmission lines Star and Delta , Star is a 4 wire connection with each phase supplying potential with respect to a common ground wire , while delta is 3 wire connection with any single phase at one given time acting as a ground , for transmission reducing one wire makes a lot of cost difference hence it is favored

In which phase are initial technology, engineering, integration, and life-cycle cost risk-reduction activities conducted?

44836.82577 Hz

Circuit patterns are the collections of transistors, capacitors, and associated components and their interconnections.

Phone will charge faster with a larger charging current. Charging current depends on voltage, so your home charger likely has a higher voltage and therefore a higher charging current.

What it means is that those rated values may not be exceeded, they are the maximum that the machine can take.

I have two Different Signals, I would like to find the RMS Error Between them, and Mathematically derive how the signals differ from each other.

I would like to find the RMS Error for the two Signals. Please Help.

Thanks in Advance.

Yes.

turn on and turn off a device and act as a switch is called as zvs

A: I could tell you but it is better if you learn how to do it on your own look up datasheetlocator.com LM78XX . For these numbers there are SOT-223 and TO-252 and TO-220. These numbers specify packaging You probably have TO-220 in that case looking from the top left is adj vout vin. The metal can be Vout again it depends on the packaging use a VOM to ascertain the metal tab connection.

Output voltage (...of a transformer, for example...) will decrease as it is loaded because of the transformer's internal resistance. As output current increases/load resistance decreases, a larger voltage will be dropped across the internal transformer resistance.

This same phenomenon is present in AC and DC systems (such as batteries).

All switches have a breaking capacity. The number 60947-3 is not a switch number it is an IEC standards publication that relates to panel mounted switches. The publication sets out specifications that manufacturers have to adhere to so as to get their equipment approved for use.

yes,ignition coil can also be used to energise the Tesla coil very well ,because it is also a type of high voltage potential transformer and it can be used in manner of fly back configuration used this and I'm satisfied that it works same as other H.V t/f just there is need of little modification required to energise it and its output also i.e square wave to sinewave...

Emf (voltage) =2p phi N Z divided by 60c

p= no of pairs of poles

phi = flux

N =speed (rpm)

Z = can't remember

c = no. of parralel paths

if you can make the values of the other parts of the formula such that the result is 5 kv your on

this is initially a dc generator but can be made to apply to ac